Control of W-ECO MULTI SYSTEM
3
TD831077
III - 53
(A) Setting the current time
¶ Set the current time. (Ex: When the current time is
11 hrs. 45 min.)
1 Holding the SET button pressed, press the HH.
button and adjust the current time.
¶ When the HH. button is
pressed every time
while holding the SET
button pressed, the hour
is successively counted.
¶ When the HH. button is
held pressed while
holding the SET button
pressed, the hour is fast
fed.
(Ex: To set the hour at
11 hours, release the
button at 11).
¶ When the SET button is
released, the hour is set
and it changes from
flashing to ON.
2 Holding the SET button pressed, press the MM.
button and adjust the current time.
¶ When the MM. button is
pressed every time
while holding the SET
button pressed, the
minute is successively
counted.
¶ When the MM. button is
held pressed while
holding the SET button
pressed, the hour is fast
fed.
(Ex: To set the minute
at 45 minutes, release
the button at 45).
¶ When the SET button is
released, the minute is
set and it changes from
flashing to ON.
¶ The time cannot be changed by pressing only the
HH. and MM. buttons.
¶ If the DAY, HH., or MM. button is not pressed while it
is flashing, the original display (regular display) is
automatically restored after lapse of 30 seconds.
Repeat the operation from the beginning.
CHECK
CANCEL
CLEAR
PROGRAM
DAY
HH
MM
SET
Su Mo Tu We Th Fr Sa
PROGRAM ERROR
OFFON
PROGRAM 1
PROGRAM 2
PROGRAM 3
CLOCK
1038_1143
1090_1143
CHECK
CANCEL
CLEAR
PROGRAM
DAY
HH
MM
SET
Su Mo Tu We Th Fr Sa
PROGRAM ERROR
OFFON
PROGRAM 1
PROGRAM 2
PROGRAM 3
CLOCK
1039_1143
1091_1143
(B) Setting the day
¶ Set today’s day. (Ex: On Wednesday)
1 Holding the SET button pressed, press the DAY
button and adjust the today’s day.
¶ When the DAY button is
pressed while holding
the SET button pressed,
the current day display
“∞” starts flashing and
the day successively
changes as follows.
The day is set as soon
as the SET button is
released, and it
changes from flashing
to ON.
¶ The day cannot be changed by pressing only the
DAY button.
¶ If the DAY, HH., or MM. button is not pressed while it
is flashing, the original display (regular display) is
automatically restored after lapse of 30 seconds.
Repeat the operation from the beginning.
(C) Setting program operation
The program operation can be set up to 3 cycles per
day (only 1 or 2 cycles can be also set).
The following points can be set in program operation.
¶ Setting the ON → OFF times (ON only cannot be
set).
Display of program operation, and its names
Ex: To set the program operation of Monday at the
following times.
From 8:00 to 12:00
From 12:40 to 16:50
From 17:00 to 19:00
CHECK
CANCEL
CLEAR
PROGRAM
DAY
HH
MM
SET
Su Mo Tu We Th Fr Sa
PROGRAM ERROR
OFFON
PROGRAM 1
PROGRAM 2
PROGRAM 3
CLOCK
10 40_1143
Su Mo Tu We Th Fr Sa
1089_1143
NOTE
NOTE
CHECK
CANCEL
CLEAR
PROGRAM
DAY
HH
MM
SET
Su Mo Tu We Th Fr Sa
PROGRAM ERROR
OFFON
PROGRAM 1
PROGRAM 2
PROGRAM 3
CLOCK
10 41_1143
Operating time of
program 1
Operating time of
program 2
Operating time of
program 3
2. Optional Controller (weekly timer)
To Next Page
Loading...
