What causes a 'Saver error' on my SATO Label Maker?
If your SATO Label Maker displays a 'Saver error', it means the print head cannot stop at the specified position. Adjust the saver head position. Replace the saver sensor. Replace the saver motor and motor driver PCB. Replace the saver cam.
What to do if the SATO Label Maker shows a paper end error?
If your SATO Label Maker displays a paper end error, it could be due to several reasons. First, ensure that the media is loaded correctly. Check also that the media sensor is clean and that its cable is properly connected. Adjust the sensor level if the sensitivity is not set correctly. If the media is jammed, remove it.
Why am I getting a download data error on my SATO Label Maker?
A download data error on your SATO Label Maker can occur if the downloaded data is incorrect or if the download area is insufficient. Check the downloaded data and the downloaded data size.
What to do if my SATO s84ex Label Maker shows a 'Paper end' error?
If your SATO Label Maker displays a 'Paper End' error, it means the media is either not loaded, not loaded correctly, has jammed, or the media sensor is dirty or has a disconnected cable. First, load the media correctly and remove any jammed media. Then, clean the media sensor and ensure its cable is correctly connected. You may also need to adjust the sensor level.
What to do if my SATO s84ex Label Maker displays a 'Ribbon end' error?
If your SATO Label Maker displays a 'Ribbon End' error, it could be due to several reasons: the ribbon is not loaded, damaged, or not loaded correctly, or the ribbon is torn. To resolve this, load a new ribbon correctly. If the ribbon is torn, clean and adjust the ribbon path.
What to do if my SATO Label Maker shows a 'Head open' error?
If your SATO Label Maker shows a 'Head open' error, it means the print head is unlocked or the sensor for sensing the open/close status of the print head is defective. Make sure the print head is locked. If the problem persists, the sensor may need to be replaced.
What to do if my SATO Label Maker displays a 'Cover open error'?
If your SATO Label Maker shows a 'Cover open error', it means the cover is opened or the sensor for sensing the open/close status of the cover is defective. Ensure the cover is securely closed. If the error continues, the sensor may need replacement.
What to do if my SATO Label Maker shows an 'Overheat error'?
If your SATO Label Maker is overheating, it means the printer's temperature has exceeded its tolerance. Stop using the printer and allow it to cool down.
What to do if my SATO Label Maker displays a 'Sensor error'?
If your SATO Label Maker displays a 'Sensor error', it could be due to an incorrect media sensor level, an incorrect sensor type, or meandering media. Adjust the media sensor level and ensure you are using the correct sensor type. If the media is meandering, clean and adjust the media path.
What to do if my SATO s84ex Label Maker displays a 'Print head error'?
If your SATO Label Maker displays a 'Print head error', it could be because the print elements are worn out or the print head is damaged. If the print elements are worn out, change print head check conditions to only check for missing elements in barcodes and try to adjust missing elements to white bars. If the print head is damaged, it needs to be replaced.
General| Max Print Length | 39.37 inches |
|---|---|
| Print Method | Thermal Transfer / Direct Thermal |
| Connectivity | USB, Serial |
| Supported Barcode Types | Data Matrix, PDF417, QR Code |
| Supported Media Types | Roll, Fanfold |
| Media Thickness | 0.002 to 0.008 inches |
| Operating Temperature | 41 to 95°F (5 to 35°C) |
| Dimensions | 18.11" D x 12.6" H |
| Print Width | 4.09 inches |
| Max Print Width | 4.09 inches |
| Memory | 16MB Flash, 32MB SDRAM |
Outlines essential safety and environmental considerations for printer installation.
Explains how to connect the printer to host computers using various available interfaces.
Details the procedure for safely connecting the printer to an AC power source.
Describes the correct steps for powering the printer on and off to prevent malfunctions.
Provides step-by-step instructions for loading the ribbon into the printer correctly.
Outlines the process for loading media, with or without a dispenser, into the printer.
Provides intervals and procedures for cleaning essential print head and platen roller components.
Lists common printer errors, their causes, and corresponding countermeasures for resolution.
Provides a systematic checklist for diagnosing and resolving common printer operational issues.
Offers specific steps for troubleshooting issues related to various printer interface connections.
To Next Page
