Why am I getting a download data error on my SATO Label Maker?
A download data error on your SATO Label Maker can occur if the downloaded data is incorrect or if the download area is insufficient. Check the downloaded data and the downloaded data size.
What to do if my SATO s84ex Label Maker shows a 'Paper end' error?
If your SATO Label Maker displays a 'Paper End' error, it means the media is either not loaded, not loaded correctly, has jammed, or the media sensor is dirty or has a disconnected cable. First, load the media correctly and remove any jammed media. Then, clean the media sensor and ensure its cable is correctly connected. You may also need to adjust the sensor level.
What to do if my SATO s84ex Label Maker displays a 'Ribbon end' error?
If your SATO Label Maker displays a 'Ribbon End' error, it could be due to several reasons: the ribbon is not loaded, damaged, or not loaded correctly, or the ribbon is torn. To resolve this, load a new ribbon correctly. If the ribbon is torn, clean and adjust the ribbon path.
What to do if my SATO Label Maker shows a 'Head open' error?
If your SATO Label Maker shows a 'Head open' error, it means the print head is unlocked or the sensor for sensing the open/close status of the print head is defective. Make sure the print head is locked. If the problem persists, the sensor may need to be replaced.
What does a framing error mean on my SATO s84ex?
A framing error on your SATO Label Maker indicates that the RS-232C settings are incorrect or the cable connection is faulty. To solve this, adjust the interface settings correctly and check that the cable is properly connected.
How do I resolve a sensor error on my SATO s84ex?
A sensor error on your SATO Label Maker could be due to an incorrect media sensor level, the wrong sensor type, or meandering media. Adjust the media sensor level, ensure you are using the correct sensor type, and clean and adjust the media path.
Why is my SATO s84ex Label Maker showing a memory write error when using USB memory?
A memory write error on your SATO Label Maker when using USB memory can occur for several reasons. The USB memory might be disconnected during writing, or there might not be sufficient copy area in the memory. Also, writing to the memory may fail, or the USB memory might not be formatted. Ensure the USB memory is connected, has sufficient copy area, and is properly formatted. If the issue persists, try replacing the memory.
What to do if the SATO Label Maker shows a paper end error?
If your SATO Label Maker displays a paper end error, it could be due to several reasons. First, ensure that the media is loaded correctly. Check also that the media sensor is clean and that its cable is properly connected. Adjust the sensor level if the sensitivity is not set correctly. If the media is jammed, remove it.
What to do if my SATO Label Maker displays a 'Sensor cover open error'?
If your SATO Label Maker displays a 'Sensor cover open error', it means the sensor cover is unlocked or the sensor for sensing the open/close status of the sensor cover is defective. Ensure the sensor cover is locked. If the error persists, the sensor may need to be replaced.
What to do if my SATO s84ex Label Maker displays a 'Parity error'?
If your SATO Label Maker displays a 'Parity error', 'Overrun error', or 'Framing error', it is likely due to incorrect RS-232C settings or an incorrect cable connection. Adjust the interface settings correctly and ensure the cable is properly connected.
General| Max Print Length | 39.37 inches |
|---|---|
| Print Method | Thermal Transfer / Direct Thermal |
| Connectivity | USB, Serial |
| Supported Barcode Types | Data Matrix, PDF417, QR Code |
| Supported Media Types | Roll, Fanfold |
| Media Thickness | 0.002 to 0.008 inches |
| Operating Temperature | 41 to 95°F (5 to 35°C) |
| Dimensions | 18.11" D x 12.6" H |
| Print Width | 4.09 inches |
| Max Print Width | 4.09 inches |
| Memory | 16MB Flash, 32MB SDRAM |
To Next Page
