SATO s84ex - Connector Pin Assignment

437
8.2 Connector Pin Assignment
No
Signal name
Description
Input/
Output
Level
Electrical conditions
Voltage, Current (MAX)
25 pins
14 pins
1
14
FG
FRAME GROUND
-
-
-
2
-
+5V
Power source
-
-
600mA
(When at 25 pin, the
total of 2 pin and 12 pin
is 600mA)
3
-
-
-
-
-
-
4
4
Machine error*4
Output with cover open, head error,
communication error and so on.
Output
Low
400V
80mA
5
6
Print completion signal
(PREND)*
Signal is output at the operation of
the printer issues one label.
Output
Low
400V
80mA
6
9
Online *3
Output when the printer is offline
state.
Output
Low
400V
80mA
7
-
Label near end
By input of this signal, the printer
becomes label near end status.
Input *2
Low
High: high impedance
Low: more than -5mA,
0V
8
7
Reprint signal
(PRIN2)
By input of this signal, the printer
reprints the same contents for one
time.
Input *2
Low
High: high impedance
Low: more than -5mA,
0V
9
-
-
-
-
-
-
10
-
-
-
-
-
-
11
-
OUT_COM
GROUND of peripherals
-
-
-
12
13
+5V
Power source
-
-
600mA
(When at 25 pin, the
total of 2 pin and 12 pin
is 600mA)
13
12
+24V
Power source
-
-
2A
14
2
GND
SIGNAL GROUND
-
-
-
15
2
OUT_COM
GROUND of peripherals
-
-
-
16
3
Ribbon end*4
Output at ribbon end detection.
Output
Low
400V
80mA
17
1
Paper end*4
Output at paper end detection.
Output
Low
400V
80mA
18
10
Ribbon near end
Output at ribbon near end
detection.
Output
High
400V
80mA
19
-
-
-
-
-
-
20
5
Print start signal
(PRIN)
The printer issues one label by
input of this signal.
Input *2
Low
High: high impedance
Low: more than -5mA,
0V
21
11
Label feed
The printer feeds by input of this
signal.
Input *2
Low
High: high impedance
low: more than -5mA,
0V
22
-
-
-
-
-
-
23
-
-
-
-
-
-
24
13
IN_COM *1
For power supply from peripherals.
Input
-
5V - 24V or GND
25
-
GND
SIGNAL GROUND
-
-
-
1) Please select one type from TYPE I to TYPE IV for "PREND" output signal of No. 5 pin. Refer to external signal type in "8.1Basic
Specifications " for more details.
[Supplemental explanation]
The pin No. and signal name (contents) can be changed on the extended setting mode. Refer to the item of "Input/Output signal
setting" in the "Operator Manual" for more details.
[Notes]
*1 When use the 14 pins external signal interface, be not connect the power pin to ｢IN_COM｣pin.
The ｢IN COM｣ pin is connect to ｢5V｣ in cable.
*2 It can be connected to equipment of open collector input to the signal input terminal.
*3 This is when “EXT 9PIN SELECT” in the service mode is MODE2. Signal is output with remaining print number status when
it is MODE1.
*4 Refer to Appendix in the operator manual for pin assignment when RFID module is enabled.