Home
SED
Controller
024.16.720
SED 024.16.720 User Manual
60 pages
Manual
Specs
Ask a question
To Next Page
To Next Page
Loading...
Montageanleitung / Operating Instructions
T
ype 024.16.720
Elektropneumatischer Stellungsr
egler
Electropneumatic position contr
oller
2
Table of Contents
Default Chapter
3
Table of Contents
3
1 EC Declaration of Conformity
8
2 Operating Instructions
9
Symbols
9
3 Authorized Use
10
Restrictions
10
Predictable Misuse
10
4 BASIC Safety Instructions
11
5 General Information
12
Scope of Supply
12
Contact Addresses
12
Warranty
12
Trademarks
13
Information on the Internet
13
6 System Description
14
Intended Application Area
14
Function of the Positioner and Combination with Valve Types
14
Features of the Valve Types
15
Structure of the Positioner
16
Representation
16
Features
17
Function Diagram of the Positioner with Single-Acting Actuator
18
Type 024.16.720 Positioner with Position Controller
19
Schematic Representation of the Position Control Type 024.16.720
19
Properties of the Position Controller Software
20
Interfaces of the Positioner
22
7 Technical DATA
23
Operating Conditions
23
Conformity
23
Mechanical Data
23
Pneumatic Data
24
Adhesive Labels
24
Label (Example)
24
Identification Label Of The Ignition Protection Classes
24
Electrical Data
25
Electrical Data Without Bus Control 24 V DC
25
Electrical Data with as Interface Bus Control
25
Factory Settings of the Positioner
26
8 Control and Display Elements
27
Operating Status
27
Control and Display Elements of the Positioner
27
Configuration Of The Keys
28
Function of the Dip Switches
29
Display of the Leds
30
Error Messages
31
Error Messages in Manual and Automatic Operating Statuses
31
Error Messages While the X.TUNE Function Is Running
31
9 Installation
32
Safety Instructions
32
Installing the Positioner Type 024.16.720
33
Rotating the Positioner for Process Valves
37
10 Fluid Installation
38
Safety Instructions
38
Installing the Process Valve
38
Pneumatic Connection of the Positioner
39
11 Electrical Installation 24 V DC
40
Safety Instructions
40
Electrical Installation with Circular Plug-In Connector
41
Designation of the Contacts Type 024.16.720
41
Connection of the Positioner Type 024.16.720
41
Electrical Installation with Cable Gland
43
Designation of the Screw-Type Terminals
43
Connection of the Positioner Type 024.16.720
43
12 AS Interface Installation
45
AS Interface Connection
45
Technical Data for as Interface Pcbs
45
Programming Data
45
Led Status Display
46
Electrical Installation as Interface
47
Safety Instructions
47
Connection with Circular Plug-In Connector M12 X 1, 4-Pole, Male
47
Connection with Multi-Pole Cable and Ribbon Cable Terminal
48
13 START-Up
49
Safety Instructions
49
Specifying the Standard Settings
49
Running the Automatic Adjustment X.TUNE
50
14 Operation and Function
51
Basic Functions
51
DIR.CMD - Effective Direction of the Position Controller Set-Point Value
52
CUTOFF - Sealing Function for the Position Controller
53
CHARACT - Select the Transfer Characteristic between Input Signal
54
Value) and Stroke
54
Auxiliary Functions
55
15 Safety Positions
56
Safety Positions after Failure of the Electrical or Pneumatic Auxiliary Power
56
Need help?
Do you have a question about the SED 024.16.720 and is the answer not in the manual?
Ask a question
SED 024.16.720 Specifications
General
Category
Controller
Input Voltage
24V DC
Output Current
16A
Power
384W
Protection
Overload, Short Circuit, Overvoltage
Need help?
General
To Next Page