MX-M260/M310/M260N/M310N SIMULATION 6 - 33
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Operation/procedure
1. Select “1: COPY START.”
The currently set value is highlighted beside the item.
2. Enter the correction value with the 10-key, and press the [#/P] key.
3. Press the [START] key.
Copying is started.
There is no tray selection operation.
The optimum paper tray for the scanned size is selected.
4. Select the scanning method.
Even when the SPF/RSPF is selected, if there is no original on the
SPF/RSPF, the OC is scanned.
Even when the OC is selected, if there is any original on the SPF/
RSPF, the SPF/RSPF is scanned. (Setting 2)
Note: Executable only when the FAX is installed.
Operation/procedure
1. Select “1: COPY START.”
The currently set value is highlighted beside the item.
2. Press the [START] key.
Copying is started.
There is no tray selection operation.
The optimum paper tray for the scanned size is selected.
When two pages are scanned, duplex print is made,
Note: Executable only when the FAX is installed.
Item Content Setting range Default
1TRAY1
1st tray 0-99
53
2OPTION
Option tray
1-99
3MANUAL
Manual feed
4DUPLEX
Back print
50-6
Purpose Adjustment
Function
(Purpose)
Used to adjust the print image position (top margin) on
print paper in the copy mode. (RSPF)
Item Picture quality Image position
Item Content
Setting
range
Default
1
SIDE1
Surface original scan start
position adjustment
1-99 50
2
SIDE2
Back original scan start
position set
1-99 50
3
END EDGE
Rear edge void adjustment
(RSPF)
1-99 50
4
LOSS(SIDE1)
Surface image loss quantity
set
1-5 3
5
LOSS(SIDE2) Back image loss quantity set
1-5 3
6
REARLOS(SIDE1)
Surface rear edge image
loss quantity set
1-5 3
7
REARLOS(SIDE2)
Back rear edge image loss
quantity set
1-5 3
50-8
The adjustments on the machine side must have been normally
completed.
Purpose Adjustment
Function (Purpose) FAX lead edge adjustment (read)
Section FAX
Normal display NOW PRINTING
Error display
DOOR OPEN
JAM
PAPER EMPTY
Item Content
Setting
range
Default
1 COPY START Copy start – –
2
SCAN
SELECT (OC/
SPF/RSPF)
Scan selection (1: OC,
2: SPF, 3: RSPF back)
1-3 1
3LEAD
Scan lead edge position
adjustment value of the
selected method in 2.
43-57 50
4 LEFT
Scan left edge position
adjustment value of the
selected method in 2.
43-57 50
5REAR
Scan rear edge position
adjustment value of the
selected method in 2.
43-57 50
6RIGHT
Scan right edge position
adjustment value of the
selected method in 2.
43-57 50
50-9
Purpose Adjustment
Function (Purpose) FAX lead edge adjustment (print)
Section FAX
Normal display NOW PRINTING
Error display
DOOR OPEN
JAM
PAPER EMPTY
Item Content
Setting
range
Default
1 COPY START Copy start – –
2LEAD
Print lead edge void
adjustment value
(Front surface)
43-57 53
3LEFT
Print left edge void
adjustment value
(Front surface)
43-57 53
4REAR
Print rear edge void
adjustment value
(Front surface)
43-57 53
5
LEAD
(DUPLEX)
Print lead edge void
adjustment value
(Back surface)
43-57 53
6 LEFT (DUPLEX)
Print left edge void
adjustment value
(Back surface)
43-57 53
7
REAR
(DUPLEX)
Print rear edge void
adjustment value
(Back surface)
43-57 53
To Next Page
Loading...
