MX-M260/M310/M260N/M310N SIMULATION 6 - 34
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key.
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Press the [START] key.
The display is shifted to the copy menu.
3. Select the paper feed tray and the print density.
Enter the adjustment value with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Operation/procedure
Select the set value with the 10-key.
50-10
Purpose Adjustment
Function
(Purpose)
Used to adjust the print image center position.
(Adjustment can be made for each paper feed
section.)
Section Image processing (ICU)
Item Picture quality Image position
Item Content Setting range Default
1
BYPASS
Manual paper feed
1-99 50
2
TRAY1
1st tray
3
TRAY2
2nd tray
4
TRAY3
3rd tray
5
TRAY4
4th tray
6
DUPLEX
Back print
50-12
Purpose Adjustment
Function
(Purpose)
Used to adjust the print image center position.
(Adjustment can be made for each document mode.)
Section Image processing
Item Picture quality Image position
Item Content Setting range Default
1
OC
OC document scan
1-99 50
2
SPF(SIDE1)
RSPF document front
surface scan
3
SPF(SIDE2)
RSPF document back
surface scan
51
51-1
Purpose Adjustment
Function
(Purpose)
Used to adjust the OPC drum separation pawl ON time.
Section
Image process
(Photoconductor/Developing/Transfer/Cleaning)
Item Operation
Item Setting range Default
1
145mm/s
1-99 50
2
122mm/s
51-2
Purpose Adjustment
Function
(Purpose)
Used to adjust the contact pressure of paper onto the
resist roller in each section (copier paper feed section,
duplex paper feed section, RSPF paper feed section).
(When the print image position varies greatly for the
paper or when a lot of paper jam troubles occur, the
adjustment is required.)
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
Item Content Setting range Default
1 BYPASS
Manual feed 1-99 50
2TRAY1
1st tray 1-99 50
3TRAY2
2nd tray 1-99 50
4TRAY3
3rd tray 1-99 50
5TRAY4
4th tray 1-99 50
6DUPLEX
Back print 1-99 70
7 SPF(SIDE1)
RSPF front surface 1-99 50
8 SPF(SIDE2)
RSPF back surface 1-99 50
51-8
Purpose Setting
Function
(Purpose)
Used to set the OPC drum separation pawl operation
inhibit. (ON/OFF)
Section
Image process
(Photoconductor/Developing/Transfer/Cleaning)
Item Operation
Item Content Setting range Default
0
ON
Enable
0-1 0
1
OFF
Disable
To Next Page
Loading...
