Siemens Sentron SB TP01 Series - Page 13

Siemens Sentron SB TP01 Series

92 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Installation

9

Figure 2.1

SB Energy-Comm Wiring to External Power Supply, PT Module, and ACCESS System

Table of Contents

Table of Contents3
Introduction5
- Product Overview5
- Principles of Operation5
- SB Encased Systems Breaker7
- Front Panel Interface8
- Overcurrent Protective Functions9
- Alarm Setpoints9
- Extended Protective Relaying9
- Metering Functions10
- Features by Model Number10
- Logs11
- Communications11
Installation12
- Quick Reference Guide12
- Unpacking and Inspection12
- Selecting a Power Source12
- Selecting a PT12
- Wiring12
- Installing the Trip Unit in a Systems Breaker14
- Inserting and Removing the Rating Plug17
- Communications19
- Removing the Trip Unit from a Systems Breaker19
- Starting up20
User Interface21
- Front Panel Display21
- Front Panel Keys21
- Menu Structure22
- Front Panel Leds23
- Idle Display Mode24
System Configuration25
- Viewing System Configuration25
- Setting System Configuration Parameters25
- Setting Other Device Parameters27
Overcurrent Protection Configuration28
- Protective Functions Menu28
- Viewing Settings29
- Long Time Fault Protection29
- Short Time Fault Protection30
- Instantaneous Fault Protection31
- Ground Fault Protection31
- Ground Fault Sensing Scheme32
Alarm Setpoints33
- Alarms33
- Overcurrent34
- Ground Overcurrent34
- Overcurrent Demand35
- Total Harmonic Distortion35
- Over Real Power36
- Over Power Demand36
- Over Reactive Power37
- Over Apparent Power37
- Under PF Lagging38
- Over PF Leading38
Extended Protective Relaying39
- Overview39
- Tripping and Alarming39
- Neutral Overcurrent40
- Current Unbalance40
- Undervoltage41
- Voltage Unbalance41
- Overvoltage42
- Reverse Power42
- Over Frequency43
- Under Frequency43
Metering44
- Overview44
- Metered Data44
- Demand Configuration46
- Harmonics46
- Metered Data Waveforms47
- Phase Balance48
- Reset Meter Data49
Logs50
- Event Log50
- Trip Log50
- Min/Max Log51
Communications53
- Overview53
- Viewing Communications Settings53
- PC Communication53
- ACCESS Communication53
- Setting the Address and Baud Rate54
- Supervisory Software55
- Remote Operation55
Operations Menu Functions56
- Overview56
- Breaker Test56
- Mechanical Counter57
- Interruption Level57
- Fault Counter57
Security58
- Overview58
- Enable Security58
- Change Password59
Testing60
- Test Set60
- Operating Instructions60
- Error Messages61
Functions and Outputs63
Time Current Characteristic Curves64
Parameter Settings70
Menu Structure78
Seabus Plus Packet79
Glossary80
Index85

Related product manuals

Preview: Siemens Sentron WL

Siemens Sentron WL

Preview: Siemens Sentron 3VA

Siemens Sentron 3VA

Preview: Siemens SENTRON 3WA

Siemens SENTRON 3WA

Siemens SENTRON 3VA1

Preview: Siemens SENTRON 3WA1

Siemens SENTRON 3WA1

Siemens SENTRON 3VA2

Siemens SENTRON 3VA27

Preview: Siemens SENTRON 3WL10

Siemens SENTRON 3WL10

Preview: Siemens SENTRON VL160X

Siemens SENTRON VL160X

Preview: Siemens SENTRON 3WA Air

Siemens SENTRON 3WA Air

Siemens SENTRON VL Series

Preview: Sensitrip III Sentron Series

Sensitrip III Sentron Series