Siemens SIMODRIVE 611-D User Manual

More user manuals on ManualsBase.com
09.95 6 NC Machine Data (NC MD), NC Setting Data (NC SD)
6.2 General machine data (general data)
Corner deceleration rate
3
Default value Lower input limit Upper input limit Units
500 +0 100 000
1 000 units/
min (IS)
Active on
NC Stop
In continuous-path operation (G64), block transitions are covered without feedrate reduction,
i.e. the path is rounded at points of discontinuity in the contour to an extent that depends on
the traversing rate.
As a result of function G62 (continuous-path operation with feedrate reduction), the tool path
feedrate is reduced to the rate entered in NC MD 3, provided the selected feedrate was
greater.
The rounding radius is thus reduced at discontinuous block transitions.
G 62
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a a a a a a a a a
a a a a a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a a a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
Exact positioningG 64
Exact positioning
Practical application:
When the traversing rate must not become zero on a block change (exact positioning) but the
feedrate in continuous-path operation is too high.
Note:
With SW 5 and higher, separate values can be set for G620/G00, G62/G01 and G62/G36.
See MD 146*, MD 148*, MD 150*.
©
Siemens AG 1992 All Rights Reserved 6FC5197- AA50 6–7
SINUMERIK 840C (IA)

Siemens SIMODRIVE 611-D Specifications

General

Brand	Siemens
Model	SIMODRIVE 611-D
Category	Control Unit
Language	English