Siemens SIMOTRAS 6SG7050 - Page 516

Connectors and binectors 01.04
12-6 SIEMENS AG 6SG7000-0BA76
SIMOTRAS HD Operating Instructions
Connector Description Normalization Function
diag., Sheet
Fixed setpoints
K0401
Fixed value 1 (P401)
16384
=
∧
100%
G120
K0402
Fixed value 2 (P402)
16384
=
∧
100%
G120
K0403
Fixed value 3 (P403)
16384
=
∧
100%
G120
K0404
Fixed value 4 (P404)
16384
=
∧
100%
G120
K0405
Fixed value 5 (P405)
16384
=
∧
100%
G120
K0406
Fixed value 6 (P406)
16384
=
∧
100%
G120
K0407
Fixed value 7 (P407)
16384
=
∧
100%
G120
K0408
Fixed value 8 (P408)
16384
=
∧
100%
G120
K0409
Fixed value 9 (P409)
16384
=
∧
100%
G120
K0410
Fixed value 10 (P410)
16384
=
∧
100%
G120
K0411
Fixed value 11 (P411)
16384
=
∧
100%
G120
K0412
Fixed value 12 (P412)
16384
=
∧
100%
G120
K0413
Fixed value 13 (P413)
16384
=
∧
100%
G120
K0414
Fixed value 14 (P414)
16384
=
∧
100%
G120
K0415
Fixed value 15 (P415)
16384
=
∧
100%
G120
K0416
Fixed value 16 (P416)
16384
=
∧
100%
G120
Start pulse for speed controller
K0451
Fixed setting value 1 for n controller I component
16384
=
∧
100% of P100
G150
K0452
Fixed setting value 1 for n controller I component, weighted
16384
=
∧
100% of P100
G150
K0453
Fixed setting value 2 for n controller I component
16384
=
∧
100% of P100
G150
K0454
Setting value 1 for n controller I component
16384
=
∧
100% of P100
G150
Control inputs, control outputs
K0500
Binary inputs, terminals 72 to 79
Bit0 = Status of terminal 72
Bit1 = Status of terminal 73
Bit2 = Status of terminal 74
Bit3 = Status of terminal 75
Bit4 = Status of terminal 76
Bit5 = Status of terminal 77
Bit6 = Status of terminal 78
Bit7 = Status of terminal 79
Bit = 0: Input is LOW
(not activated)
Bit = 1: Input is HIGH
(activated)
G117
K0501
Binary outputs terminals 81/82 to 93/94
Bit0 = Status of terminal 81/82
Bit1 = Status of terminal 83/84
Bit2 = Status of terminal 85/86
Bit3 = Status of terminal 87/88
Bit4 = Status of terminal 89/90
Bit5 = Status of terminal 91/92
Bit6 = Status of terminal 93/94
Bit = 0: Output relay has not
picked up
Bit = 1: Output relay has
picked up
G119
4 stage master switch
K0510
Setpoint of 4-stage master switch
16384
=
∧
100%
G125
General connectors
K0800
Operating status (code number) with one decimal place
K0801
Latest fault and alarm message
Low byte: Latest alarm message
If several alarms are active simultaneously, the alarm with the
lowest number if displayed here.
Value "0" means that no alarm is active.
High byte: Latest fault message
Value "0" means that no fault is active.
G189