Siemens SINUMERIK 808D - Page 151

:= 1
MD_SLMAXCUTTINGEDGENUMBER
No. of cutting edge (MD_SLMAXCUTTINGEDGENUMBER=9 is valid up to P4)
:= -1
Cutting edge number of old tool also applies to new tool.
:= -2
Cutting edge (correction) of old tool remains active until D is programmed. This means
that the old tool remains the active tool until D is programmed. In other words, the
tool on the spindle remains the programmed tool until D is programmed.
Example:
MD20270 $MC_CUTTING_EDGE_DEFAULT = 1;
After a tool change, the first cutting edge is active if no other cutting edge has been
programmed.
20272 SUMCORR_DEFAULT C03 H2, W1
- Initial position resulting offset without program DWORD PowerOn
-
808d-me42 - 0, 0, 0, 0, 0, 0, 0, 0... -1 6 ReadOnly M
808d-me62 - 0, 0, 0, 0, 0, 0, 0, 0... -1 6 ReadOnly M
808d-te42 - 0, 0, 0, 0, 0, 0, 0, 0... -1 6 ReadOnly M
808d-te62 - 0, 0, 0, 0, 0, 0, 0, 0... -1 6 ReadOnly M
808d-mte40 - 0, 0, 0, 0, 0, 0, 0, 0... -1 6 7/2 M
808d-mte60 - 0, 0, 0, 0, 0, 0, 0, 0... -1 6 7/2 M
Description: The number of the total offset of the cutting edge which becomes active when a new
cutting edge compensation is activated without a programmed DL value being available.
MD18110 $MN_MM_MAX_SUMCORR_PER_CUTTEDGE
defines the maximum useful value which can be entered.
Value Meaning
> 0 Number of the total offset
= 0 No total offset active with D programming
= 1 The total offset number for the previously programmed D is used.
Related to:
MD20270 $MC_CUTTING_EDGE_DEFAULT.
20320 TOOL_TIME_MONITOR_MASK C06, C09 -
- Time monitoring for tool in tool holder DWORD PowerOn
-
808d-me42 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0 0x7FFFFFFF ReadOnly M
808d-me62 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0 0x7FFFFFFF ReadOnly M
808d-te42 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0 0x7FFFFFFF ReadOnly M
808d-te62 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0 0x7FFFFFFF ReadOnly M
808d-mte40 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0 0x7FFFFFFF 7/2 M
808d-mte60 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0 0x7FFFFFFF 7/2 M
Description: Activation of the tool time monitoring for the tool holders and spindles 1..x.
Machine data
3.3 Channel-specific machine data
Parameter Manual
List Manual, 01/2017 151