Siemens SINUMERIK 808D - Page 157

808d-te42 3 1.0, 1.0 , 1.0, 1.0, 1.0 ,
1.0, 1.0, 1.0 , 1.0, 1.0,
1.0 , 1.0, ...
0.0 - 7/7 U
808d-te62 3 1.0, 1.0 , 1.0, 1.0, 1.0 ,
1.0, 1.0, 1.0 , 1.0, 1.0,
1.0 , 1.0, ...
0.0 - 7/7 U
808d-mte40 3 1.0, 1.0 , 1.0, 1.0, 1.0 ,
1.0, 1.0, 1.0 , 1.0, 1.0,
1.0 , 1.0, ...
0.0 - 0/0 S
808d-mte60 3 1.0, 1.0 , 1.0, 1.0, 1.0 ,
1.0, 1.0, 1.0 , 1.0, 1.0,
1.0 , 1.0, ...
0.0 - 0/0 S
Description: With temperature compensation, this machine data indicates the maximum permissible
value for the tool length for each geometry axis.
If a temperature compensation value larger than this limit value is entered, it will
be limited without an alarm.
20443 LOOKAH_FFORM EXP, C05 -
- Activate extended LookAhead BYTE NEW CONF
-
808d-me42 5 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0 2 0/0 S
808d-me62 5 0, 0, 1, 1, 1 0 2 2/2 M
808d-te42 5 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0 2 0/0 S
808d-te62 5 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0 2 0/0 S
808d-mte40 5 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0 2 7/2 M
808d-mte60 5 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0 2 7/2 M
Description: The MD specifies for which technology groups the extended LookAhead is active.
Value 0: Default LookAhead
Value 1: Extended LookAhead
Value 2: reserved
E.g. MD20443 $MC_LOOKAH_FFORM[4]=1; i.e. activation for DYNFINISH.
Entry for all dynamic G code groups.
When changing between default LookAhead and extended LookAhead or vice versa, the
continuous-path mode is interrupted by an interpolatory stop.
20463 FIFOCTRL_ADAPTION EXP, C05 -
- Adaptation of the IPO buffer control DOUBLE NEW CONF
-
- - 0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0...
0.0 1.0 1/1 M
Description: The MD defines how significantly the IPO buffer control (FIFOCTRL) should influence
the path feedrate with the buffer full.
Machine data
3.3 Channel-specific machine data
Parameter Manual
List Manual, 01/2017 157