Siemens SINUMERIK 808D - Page 177

808d-te62 - FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE...
0 - ReadOnly M
808d-mte40 - FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE...
0 - 7/2 M
808d-mte60 - FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE...
0 - 7/2 M
Description: 1: When determining the retraction direction, if mirroring of the contour is active
then the retraction
direction is also mirrored. Mirroring of the retraction direction
only refers to the directional components vertical to the tool direction.
0: Mirroring of the contour is NOT taken into account when determining the
retraction direction.
21203 LIFTFAST_MODE_MASK C09 K1
- Settings for fast retraction DWORD PowerOn
-
808d-me42 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0x0 0x1 ReadOnly M
808d-me62 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0x0 0x1 ReadOnly M
808d-te42 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0x0 0x1 ReadOnly M
808d-te62 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0x0 0x1 ReadOnly M
808d-mte40 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0x0 0x1 7/2 M
808d-mte60 - 0x0, 0x0, 0x0, 0x0,
0x0, 0x0, 0x0, 0x0...
0x0 0x1 7/2 M
Description: Bit0: Behavior of LFWP with active frame
=0 If the retraction direction is defined with LFWP, the active frame is not effective.
=1 If the retraction direction is defined with LFWP, the active frame is effective. In
this case MD21202 $MC_LIFTFAST_WITH_MIRROR has no effect.
21204 LIFTFAST_STOP_COND C09 M3
- Stop behavior with fast retraction DWORD NEW CONF
-
808d-me42 - 0, 0, 0, 0, 0, 0, 0, 0... 0 0x7FFFFFFF ReadOnly M
808d-me62 - 0, 0, 0, 0, 0, 0, 0, 0... 0 0x7FFFFFFF ReadOnly M
808d-te42 - 0, 0, 0, 0, 0, 0, 0, 0... 0 0x7FFFFFFF ReadOnly M
808d-te62 - 0, 0, 0, 0, 0, 0, 0, 0... 0 0x7FFFFFFF ReadOnly M
808d-mte40 - 0, 0, 0, 0, 0, 0, 0, 0... 0 0x7FFFFFFF 7/2 M
808d-mte60 - 0, 0, 0, 0, 0, 0, 0, 0... 0 0x7FFFFFFF 7/2 M
Description: Specifies the stop behavior of the liftfast motion under different stop conditions
Bit0: Axial NC/PLC interface signal DB380x DBX4.3 (Axial feed stop / Spindle stop) or
CP-SW limit stop or a stop by an OEM application
=0 Stop of the retraction motion in case of an axial feed stop or CP-SW limit stop or
stop by an OEM application
Machine data
3.3 Channel-specific machine data
Parameter Manual
List Manual, 01/2017 177