Siemens SINUMERIK 808D - Page 336

42466 SMOOTH_ORI_TOL - B1
degrees Maximum deviation of tool orientation during smoothing. DOUBLE Immediately
-
808d-me42 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 90. 0/0 S
808d-me62 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 90. 0/0 S
808d-te42 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 90. 0/0 S
808d-te62 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 90. 0/0 S
808d-mte40 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 90. 7/7 U
808d-mte60 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 90. 7/7 U
Description: This setting data defines the maximum tool orientation tolerance during smoothing.
The data determines the maximum permissible
angular displacement of the tool orientation.
This data only applies if an orientation tranformation
is active.
Related to:
MD20480 $MC_SMOOTHING_MODE,
SD42465 $SC_SMOOTH_CONTUR_TOL
42470 CRIT_SPLINE_ANGLE - W1, PGA
degrees Corner limit angle for compressor DOUBLE Immediately
-
808d-me42 - 36.0, 36.0, 36.0, 36.0,
36.0, 36.0, 36.0, 36.0...
0.0 89.0 0/0 S
808d-me62 - 36.0, 36.0, 36.0, 36.0,
36.0, 36.0, 36.0, 36.0...
0.0 89.0 0/0 S
808d-te42 - 36.0, 36.0, 36.0, 36.0,
36.0, 36.0, 36.0, 36.0...
0.0 89.0 0/0 S
808d-te62 - 36.0, 36.0, 36.0, 36.0,
36.0, 36.0, 36.0, 36.0...
0.0 89.0 0/0 S
808d-mte40 - 36.0, 36.0, 36.0, 36.0,
36.0, 36.0, 36.0, 36.0...
0.0 89.0 7/7 U
808d-mte60 - 36.0, 36.0, 36.0, 36.0,
36.0, 36.0, 36.0, 36.0...
0.0 89.0 7/7 U
Description: The setting data defines the limit angle from which the compressor COMPCAD interprets
a block transition as a corner. Practical values lie between 10 and 40 degrees. Values
from 0 to 89 degrees inclusive are permitted.
The angle only serves as an approximate measure for corner detection. The compressor
can also classify
flatter block transitions as corners and eliminate larger angles as
outliers on account of plausibility considerations.
42471 MIN_CURV_RADIUS EXP, C09 -
mm Minimum radius of curvature DOUBLE Immediately
-
808d-me42 - 3.0, 3.0, 3.0, 3.0, 3.0,
3.0, 3.0, 3.0...
0.0 - 0/0 S
NC setting data
Parameter Manual
336 List Manual, 01/2017