Siemens SINUMERIK 808D - Page 335

808d-mte40 - 0.1, 0.1, 0.1, 0.1, 0.1,
0.1, 0.1, 0.1...
0.000001 999999. 7/7 U
808d-mte60 - 0.1, 0.1, 0.1, 0.1, 0.1,
0.1, 0.1, 0.1...
0.000001 999999. 7/7 U
Description: Contour accuracy. This setting data can be used to define the accuracy to be maintained
for
the
path
of the geometry axes on curved contours. The lower the value and the lower
the servogain factor of the geometry axes, the greater the reduction of path feed on
curved contours.
Related to ....
MD20470 $MC_CPREC_WITH_FFW
SD42460 $SC_MINFEED
42460 MINFEED - B1, K6
mm/min Minimum path feedrate for CPRECON DOUBLE Immediately
-
808d-me42 - 1., 1., 1., 1., 1., 1., 1.,
1....
1.e-6 1.e9 0/0 S
808d-me62 - 1., 1., 1., 1., 1., 1., 1.,
1....
1.e-6 1.e9 0/0 S
808d-te42 - 1., 1., 1., 1., 1., 1., 1.,
1....
1.e-6 1.e9 0/0 S
808d-te62 - 1., 1., 1., 1., 1., 1., 1.,
1....
1.e-6 1.e9 0/0 S
808d-mte40 - 1., 1., 1., 1., 1., 1., 1.,
1....
1.e-6 1.e9 7/7 U
808d-mte60 - 1., 1., 1., 1., 1., 1., 1.,
1....
1.e-6 1.e9 7/7 U
Description: Minimum path feedrate with the "Contour accuracy" function active. The feedrate is not
limited to below this value unless a lower F value has been programmed or the axis
dynamics do not permit it.
Related to ....
MD20470 $MC_CPREC_WITH_FFW
SD42450 $SC_CONTPREC
42465 SMOOTH_CONTUR_TOL - B1
mm Maximum contour tolerance on smoothing DOUBLE Immediately
-
808d-me42 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 999999. 0/0 S
808d-me62 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 999999. 0/0 S
808d-te42 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 999999. 0/0 S
808d-te62 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 999999. 0/0 S
808d-mte40 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 999999. 7/7 U
808d-mte60 - 0.05, 0.05, 0.05, 0.05,
0.05, 0.05, 0.05, 0.05...
0.000001 999999. 7/7 U
Description: This setting data defines the maximum tolerance for smoothing the contour.
Related to:
MD20480 $MC_SMOOTHING_MODE,
SD42466 $SC_SMOOTH_ORI_TOL
NC setting data
Parameter Manual
List Manual, 01/2017 335