Need help?Do you have a question about the Sirona CEREC MC and is the answer not in the manual?
General| Model | CEREC MC |
|---|---|
| Technology | CAD/CAM |
| Software | CEREC Software |
| Connectivity | Network connection |
| Materials | Ceramics, composites |
| Manufacturer | Sirona Dental Systems |
| Application | Dental restorations |
Provides contact details for technical questions and customer support.
Explains warning symbols and their meanings for safety.
Defines text formats and symbols used throughout the manual.
Clarifies the use of PC and acquisition units in the document.
Details the CE mark and relevant standards for the product.
Specifies the intended applications and indications for the system.
Describes additional applications, including optical impression.
Covers prerequisites, maintenance, and repair safety rules.
Guidelines for using approved accessories and safety precautions.
Addresses chamber door safety, phone interference, and data transmission.
Instructions for safe transport, unpacking, and incoming inspection.
Specifies environmental and physical requirements for installation.
Steps and notices for initial startup and commissioning.
Identifies the main components and controls of the unit.
Details unit ports, connections, and the machining room layout.
Lists standard accessories like instruments, calibration pins, and torque wrench.
Explains the unit's display interface and lighting indicators.
Instructions for using the processing chamber screen.
Procedure for connecting the optional bar code reader.
Steps for connecting the unit to a PC via LAN and power supply.
Covers manual installation, removal, and connecting the suction device.
Instructions for connecting the power cord to the suction system.
Guides on connecting interface cables and setting up automatic mode.
Details on adjusting suction power for optimal performance.
Steps for establishing a wireless connection to the PC via WLAN.
Guidance on optimal placement of the access point for reliable WLAN.
Instructions for operating multiple units using a single access point.
Setup procedures for specific wireless modules and network creation.
Procedure for filling the water tank with coolant additive.
Detailed instructions for the MC / MC X water tank.
Detailed instructions for the CEREC MC XL Basic water tank.
Step-by-step guide for powering the unit on and off.
Instructions for repacking the unit and checking the scope of supply.
Guidelines for storing the unit safely and effectively.
How to configure settings for CEREC MC/MC X units via software.
Details on activating and using the bar code reader feature.
Information on the extraction unit's role in dry milling.
Procedure for calibrating the milling and grinding unit.
Steps for correctly inserting calibration tools.
Guide to initiating and completing the unit calibration.
Instructions for inserting instruments after calibration.
Steps to complete and exit the calibration configuration.
Procedure for replacing the set screw on the unit.
Introduction to machining processes and instrument types.
Details on instruments used for grinding processes.
Information on milling instruments, activation, and torque wrenches.
Guidance on allowed combinations of instruments for processes.
Steps required before starting the machining process.
Procedure for initiating the machining process.
Instructions for safely concluding a machining process.
Importance of material seals of approval for quality results.
Procedure for entering bar codes for material identification.
Detailed steps for manually clamping the block securely.
Routine maintenance tasks and intervals for the unit.
Procedure for cleaning the processing chamber.
Instructions for using the specialized tool for tank caps.
Guidance on using the cleaning hose for wet cleaning.
Steps for replacing the filter bags in the suction device.
Procedure for replacing the HEPA filters.
General advice on water changes and preventing odors.
Specific instructions for replacing the filter in MC / MC X water tanks.
Specific instructions for replacing the filter in MC XL Basic water tanks.
Steps to drain water from the unit for transport or storage.
Detailed guide on using the tank cap opener for specific tasks.
Lists materials and instruments used with the system.
Details instruments compatible with the CEREC MC.
Details instruments compatible with the CEREC MC X.
Procedure for replacing instruments in the unit.
Step-by-step guide for replacing worn or defective instruments.
Instructions for replacing an instrument that breaks during use.
Guidance on approved agents for cleaning and disinfection.
Procedures for cleaning external surfaces of the unit.
Instructions for disinfecting unit surfaces.
Advice on protecting surfaces from chemical damage.
General cleaning recommendations for the unit.
Instructions for safely replacing the main fuses.
Procedure for changing the filter insert in the water tank.
Specifics for filter replacement in the MC XL Basic water tank.
Specifies hardware and software requirements for CEREC MC.
Specifies hardware and software requirements for CEREC MC X.
Provides a general technical overview of the grinding/milling unit.
Lists key technical specifications like voltage, power, and dimensions.
Information on the unit's controller board components.
Catalog of grinding instruments with reference numbers.
Catalog of milling instruments with reference numbers.
Lists filters, hoses, torque wrenches, and other consumables.
Guidance on the proper disposal of old electrical and electronic devices.
To Next Page