SMC Networks HRSH150-A*-40 Series - Hrsh100;150;200;250;300-A-40-

HRX-OM-Q026
Chapter 8 Documents
8.1 Specifications HRSH Series
8-2
8.1.2 HRSH100/150/200/250/300-A-40-
Table 8-2 Specifications of HRSH100/150/200/250/300-A-40-
Model
HRSH100-A-
40-
HRSH150-A-
40-
HRSH200-A-
40-
HRSH250-A-
40-
HRSH300-A-
40-
Cooling method
Air-cooled refrigeration
Refrigerant
R410A (HFC) (GWP1975)
Quantity of refrigerant
kg
1.27
2.1
2.1
2.8
2.8
Control method
PID control
Ambient temperature

1
o
C
-20 to 45
Circulating
fluid
system
Circulating fluid

2
Clear water, 15 to 40% ethylene glycol aqueous solution, DI water (pure water)
Set temperature range

1
o
C
5 to 35
Cooling capacity

3
kW
10.5
15.7
20.5
25
28
Heating capacity

4
kW
2.5
3
5.5
7.5
7.5
Temperature stability

5
o
C
±0.1
Pump
capacity
Rated flow rate
(Outlet)
L/min
45 (0.43 MPa)
45 (0.45 MPa)
125 (0.5 MPa)
Maximum flow rate
L/min
120
130
180
Maximum lifting
height
m
50
80
Settable pressure range

6
MPa
0.1 to 0.5
0.1 to 0.8
Minimum necessary flow
rate

7
L/min
20
25
40
Tank capacity
L
25
42
60
Port size
Rc1 (Symbol F: G1, Symbol N: NPT1)
Tank port size
Rc3/4 (Symbol F: G3/4, Symbol N: NPT3/4)
Automatic
water fill
function
(Standard
)
Supply side
pressure range
MPa
0.2 to 0.5
Supply side
water temp. range
o
C
5 to 35
Automatic water fill port
size
Rc1/2 (Symbol F: G1/2, Symbol N: NPT1/2)
Over flow port size
Rc1 (Symbol F: G1, Symbol N: NPT1)
Fluid contact part material
Metal
Stainless steel, Copper (Brazing filler metal for the heat exchanger), Bronze, Brass,
Resin
PTFE, PU, FKM, EPDM, PVC, NBR, POM, PE, NR
Electrical
system
Power supply
3 phase 380 to 415 VAC (50/60Hz)
Allowable voltage fluctuation ±10% (No continuous voltage fluctuation)
Applicable earth
leakage
breaker

(Standard)
Rated
current
A
20
30
Sensitivity
current
mA
30
Rated operating current

5
A
7.4
9.3
12.8
16
18
Rated power
consumption

5
kW
(kVA)
4.6 (5.1)
5.8 (6.4)
8.2 (8.9)
10.1 (11.1)
10.8 (12.3)
Noise level (Front: 1m, height: 1m)

5
dB(A)
68
71
Water-proof specification
IPX4
Accessories
Alarm code list label 2 pcs. (English 1, Japanese 1), Operation manual (for
installation/operation) (English 1, Japanese 1),Y-strainer (40 mesh) 25A, Barrel nipple 25A,
Anchor bracket 2pcs. (including 6 pcs. of M8 bolts)

8
Weight (in the dry state)
kg
Approx. 180
Approx. 215
Approx. 280
Standards
CE Mark
EMC Directive
2004/108/EC
Machinery Directive
2006/42/EC
1: When the ambient temperature or circulating fluid temperature is 10
o
C or below, refer to "3.2.2 Operation at low ambient temperature or low
circulating fluid temperature".
2: Use fluid for circulating fluid that conforms to:
Clean water: Water Quality Standards of the Japan Refrigeration and Air Conditioning Industry Association (JRA GL-02-1994)
15 to 40% ethylene glycol aqueous solution: Diluted with clean water, without any additives such as antiseptics. (Refer to "3.2.2 Operation at low
ambient temperature or low circulating fluid temperature" for the concentration of the ethylene glycol aqueous solution.)
DI water (pure water): Electrical conductivity 1 μS/cm or more (electrical resistivity 1MΩ・cm or less)
3 Ambient temperature: 32
o
C, (2) Circulating fluid: Clean water, (3) Circulating fluid temperature: 20
o
C, (4) Circulating fluid flow rate: Rated flow
rate, (5) Power supply: 400 VAC
4: (1) Ambient temperature: 32
o
C, (2) Circulating fluid: Clean water, (3) Circulating fluid flow rate: Rated flow rate, (4) Power supply: 400 VAC
5: (1) Ambient temperature: 32
o
C, (2) Circulating fluid: Clean water, (3) Circulating fluid temperature: 20
o
C, (4) Load: Refer to the specified cooling
capacity (5) Circulating fluid flow rate: Rated flow rate, (6) Power supply: 400 VAC, (7) Piping length: Minimum
6: With pressure control function using an inverter. When the pressure control function is not being used, the pump power supply frequency setting
function can be used.
7: Required flow rate to maintain the cooling capacity. When the flow rate is lower than the rated flow, use a by-pass piping set.
8: The anchor brackets (including M8 bolt x 6pcs.) are used for fixation with the skid when this product is packed. The anchor bolts are not attached.