STR-DA5500ES
18
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A.
DIRECT], [MUSIC], [MOVIE (HD-D.C.S.)] button in order, the message “MENU SPECIALIZED !” appears.
2. Press the [M]/[m] buttons of the remote commander, the message “<<< SPECIAL >>>” appears.
3. Press the [,] button of the remote commander, the item is appears.
4. Each time the [M]/[m] buttons of the remote commander is pressed, the item is switched in order as follows.
Some items can change the content. Display the cursor by pressing the [
,] button of the remote commander, and changing the content
by pressing the [M]/[m] buttons of the remote commander, and fi x the content by pressing the [<] button of the remote commander
when you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE (HD-
D.C.S.)] button in order again, the message “MENU SPECIALIZE OFF” appears.
Items Display Remark
SYSTEM version display SYSTEM VERSION X.XXX X.XXX: System software version
MAIN Ucom version display
MAIN ##### ∗∗∗ vX. XX
#####: Model
∗∗∗: Destination
X.XX: Main controller software version
Video Ucom version display Video Ucom Ver X. XX X.XX: Video system controller software version
FAROUDJA version display FAROUDJA Ver X. XX X.XX: Video processor software version
GUI CG-ROM version display GUI CGROM Ver X. XX X.XX: CG-ROM software version
DSP Ucom version display DSP Ucom Ver X. XX X.XX: DSP controller version
DSP serial fl ash version display DSP SFLASH Ver X. XX X.XX: DSP serial fl ash software version
DSP parallel fl ash version display DSP PFLASH Ver X. XX X.XX: DSP parallel fl ash version
IR learning Ucom version display IR LEARNING Ver X.XX X.XX: IR learning software version
Network processor version
NTE 09A55∗∗ Ver X.XX ∗∗: Destination
X.XX: Network processor software version
DSP debug menu <DSP DEBUG MENU> Not used for the servicing
Network debug menu <NETWORK DEBUG MENU> Menu mode to enter MAC address display. If the [ENTER] but-
ton of the remote commander is pressed, entering the menu,
and operating the following menu become possible
MAC address display
(Network debug menu)
MAC∗∗:∗∗:∗∗:∗∗:∗∗:∗∗ ∗∗:∗∗:∗∗:∗∗:∗∗:∗∗: MAC address
Network update check NET UPDATE CHECK? If the [Enter] button of the remote commander is pressed, the
checking result is displayed without connecting to network. OK:
“NET UPDATE CHK OK”, Path to MAIN NG: “NET UPDATE
CHK NG M”, Path to VIDEO NG: “NET UPDATE CHK NG V”,
Path to DSP NG: “NET UPDATE CHK NG D”
Zone 4 display ZONE 4 XXXXXXXX Not used for the servicing
FAROUDJA update FARO SELECT [XXXXXXX] XXXXXXX: The selector is switched for the update of the
FAROUDJA update.
[VIDEO]: Video Ucom rewriting,
[UPDATE1]: Faroudja rewriting (main),
[UPDATE2]: Faroudja rewriting (2nd),
[DEBUG1]: Faroudja debug (main),
[DEBUG2]: Faroudja debug (2nd),
HDCP key read HDCP KEY READ [XXX] Not used for the servicing
Learning Ucom check LEARNING TEST START? Not used for the servicing
Model/destination change
MODEL [##### ∗∗∗∗ XX]
Not used for the servicing
Video factory menu <VIDEO FACTORY MENU> Menu mode to enter video calibration menu and DDR access
check menu If the [ENTER] button of the remote commander
is pressed, entering the menu, and operating two the following
menu become possible
Ver. 1.1
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
Loading...
