Stulz ENS 18 A - Inspecting the electrical system

DE / 06-2016 / 1000687 © STULZ GmbH, Hamburg
-
78
-
Maintenance STULZ UltraSonic -System for duct humidication ENS 14 A - 18 A-
11.5. Inspecting the electrical system
Proceed as follows to inspect the electrical system:
3
Unscrew the screw plug of the drainage
pipe and drain the water.
4
Disconnect water supply and drainage
pipes.
5
Mark electrical supply cables and
connections.
Then disconnect them.
6
Drain residual water from the ultrasonic
humidier.
Put the ultrasonic humidier in a place
where it can be dismantled easily.
2
Close the on-site stop cock.
1
Switch off the electrical supply to the
ultrasonic humidier and secure so it
cannot be switched back on.
CAUTION
Specialist personnel.
This work may only be performed by specialist
personnel.
WARNING
Item Description
1 Ultrasonic humidier
2 Stainless steel screw
3 Housing cover of electronic supply module
Slacken but do not fully remove the screws.
3
1
7
Slacken the two stainless steel screws
in the housing cover of the electronic
supply module.
Take off the housing cover.
Connections
(A) Drinking water connection
(B) Waste water connection
(C)
Overow connection
ＡＩＲ ＩＮＬＥＴ
ＭＩＳＴ ＯＵＴＬＥＴ
１０
２１ ５
３４７
９
１０
１１
ＨＵＭＩＤＩＦＩＥＲ ＣＡＳＩＮＧ
ＥＬＩＭＩＮＡＴＥＲ
ＭＥＴＡＬ ＣＯＮＮＥＣＴＯＲ
ＭＥＴＡＬ ＣＯＮＮＥＣＴＯＲ
ＷＡＴＥＲ ＳＵＰＰＬＹ ＴＵＢＥ
ＯＶＥＲＦＬＯＷ ＰＩＰＥ
ＤＲＡＩＮ ＰＩＰＥ
ＭＯＵＮＴＩＮＧ ＦＯＯＴ
ＷＡＴＥＲ ＳＵＰＰＬＹ ＶＡＬＶＥ
ＳＵＳ３０４
ＡＢＳ
４Ｐ
３Ｐ
ＴＯ ＢＥ ＰＲＯＶＩＤＥＤ ＢＹ ＵＳＥＲ
１６ｍｍ Ｏ．Ｄ． １３ｍｍ Ｉ．Ｄ．
１２ｍｍ Ｏ．Ｄ． ８ｍｍ Ｉ．Ｄ．
ＳＵＳ３０４
ＴＯ ＢＥ ＰＲＯＶＩＤＥＤ ＢＹ ＵＳＥＲ
ＳＰＥＣＩＦＩＣＡＴＩＯＮＳ
ＭＯＤＥＬ
ＣＡＰＡＣＩＴＹ（ｋｇ／ｈ）
ＮＯＳ．ＯＦ ＵＬＴＲＡＳＯＮＩＣ
ＮＥＢＵＬＩＺＥＲ ＵＮＩＴ
ＰＯＷＥＲ ＳＵＰＰＬＹ
ＲＡＴＥＤ ＰＯＷＥＲ
ＣＯＮＳＵＭＰＴＩＯＮ（ｗ）
ＷＥＩＧＨＴ（ｋｇ）
ＤＩＭＥＮＳＩＯＮ Ｌ（ｍｍ）
ＤＩＭＥＮＳＩＯＮ Ｐ（ｍｍ）
ＥＮＳ１４Ａ
１３～１４
２４
ＡＣ４８Ｖ±１０％
７５０
１１
７８５
７３０ ８９５
９５０
１３
９６０
３０
１７～１８
ＥＮＳ１８Ａ
６
１２
ＣＯＲＤ（ＭＡＩＮ） ＳＨＩＥＬＤ ＣＡＢＬＥ ４Ｃ ４ｍ
ＣＯＲＤ（ＣＯＮＴＲＯＬ） ＳＨＩＥＬＤ ＣＡＢＬＥ ３Ｃ ４ｍ
ウエットマスター株式会社
ＣＯ ＬＴＤＷＥＴＭＡＳＴＥＲ ，．
ＷＥＴＭＡＳＴＥＲ ＥＮＳ
２００ ２３０ ２６０
７
Ｐ
Ｌ
４５ ５５ ４０
１５
４５
１０ ９５ ２０ ５０
１７５
１１０ ≒６０
３０ ６０ ２０
１５
５０
ＩＴＥＭ
１
２
３
４
５
６
７
８
９
１０
１１
ＰＡＲＴ ＮＡＭＥ ＳＰＥＣ．／ＴＹＰＥ
３０
１２
ＲＩＮＧ ＡＮＤ ＮＵＴ ６ｍｍ／６．３５ｍｍ
８
(C) (B)(A)