Why are the belts breaking on my Sukup Fastir?
Belts may be breaking due to improper alignment. To solve this, adjust the motor pulley. Another potential cause is a damaged pulley, so check the pulley and auger shaft for any damage and replace if necessary.
What to do if 1-1/2 HP motor is not turning in Sukup Fastir Farm Equipment?
If the 1-1/2 HP motor isn't turning, it could be due to a thermal overload shut off. Try pressing the reset button. Also, the motor may be running on 115V and needs to be on 230V (except on 460V units).
How to fix a Sukup Fastir crosstube that is not turning?
If the crosstube isn't turning, the shearpin on the gearmotor may have sheared. Replace the shearpin.
Why is the 1-1/2 HP motor on my Sukup Fastir Farm Equipment running slow and lacking power?
If the 1-1/2 HP motor is running slowly and lacks power, it may be wired for 115V or one fuse may be blown. Use a voltmeter to check the voltage; it must be 230V.
What causes a Sukup Farm Equipment crosstube to stop moving forward on the track?
If the crosstube isn't moving forward on the track, the shearpin on the gearmotor may have sheared. Replace the shearpin.
Why is the down auger getting ahead on my Sukup Farm Equipment?
If the down auger is getting ahead, it could be because the crosstube isn't traveling around the bin due to a hard spot or concentrations of fines in the center of the bin. Check the gearmotor and gears to ensure they are functioning correctly, and replace any damaged parts.
Why is my Sukup Farm Equipment experiencing machine vibration?
Machine vibration may be due to a bent down auger. Straighten the auger or install a new one.
Why is the down auger trailing excessively on my Sukup Fastir?
If the down auger is trailing excessively, the flighting may be worn off. Replace the auger.
What causes Sukup Fastir to hit the top of the bin?
If the machine is hitting the top of the bin, the track may be installed too high. Lower the track.
What to do if the carriage isn't traveling in or out of the crosstube in Sukup Farm Equipment?
If the carriage isn't traveling in or out of the crosstube, the reversing mechanism bearing may not have switched completely. Adjust the springs on the reversing rod to make each side equal. Also, check the detent and spring, and verify the toggle gear bolt torque, which should be approximately 30 ft-lbs.
Safety guidelines specific to grain bin operations.
Requirements and recommendations for PPE.
Procedures and contact information for emergency situations.
Instructions for applying and replacing safety decals.
Step-by-step guide for installing the track system.
Procedures for assembling and mounting the machine carriages.
Steps for mounting and securing the machine motors.
Instructions for timing and adjusting the reversing mechanism.
Electrical wiring steps for the gearmotor.
Steps for installing the down augers onto the carriage.
Concluding installation tasks and checks.
How to start, operate, and manage the machine during drying.
Routine checks and maintenance for the machine.
Procedures for testing gearmotor continuity and function.
How to check and adjust the reversing mechanism alignment.
Fundamentals of grain drying, airflow, and temperature effects.
Factors and formulas for choosing the correct heater.
Proper placement of fans, heaters, and controllers on bins.
Warnings and guidelines to prevent fires during grain drying.
Guidelines for safe grain storage, moisture content, and duration.
Purpose and methods of grain aeration for temperature control.
Regular maintenance checks for the grain bin and associated systems.
Wiring diagrams for single auger configurations.
Wiring diagrams for double auger configurations.
Wiring diagrams for triple auger configurations.
Wiring diagrams for four auger configurations.
Detailed parts list and diagrams for the track assembly.
Parts and diagrams for the center hanger assembly.
Parts and diagrams for wrap-around carriage assemblies.
Detailed parts list and diagrams for the primary carriage.
Detailed parts list and diagrams for the satellite carriage.
Parts and diagrams for the stationary outside carriage.
Parts and diagrams for the electrical junction box.
Parts and diagrams for the reversing mechanism assembly.
Parts and diagrams for the rotating contact assembly.
Parts and diagrams for the gearmotor.
Table detailing cord lengths for various configurations.
Table listing electrical components by model and size.
General| Brand | Sukup |
|---|---|
| Model | Fastir |
| Category | Farm Equipment |
| Type | Grain Dryer |
| Construction | Galvanized steel |
| Fuel Type | Propane or Natural Gas |
To Next Page
