Home
SunStar
Engine
Fortuna series
SunStar Fortuna series User Manual
5
of 1
of 1 rating
86 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
9
9
.
Clean it every two or three weeks so that no dirt or a dirty
substance may be piled up.
10.
When replacing the fuse, use a standard item, opening the
cover as shown in the diagram.
11.
Make the length of the cable connected with an outside parts
like stand-up pedal as short as possible.
7
9
Table of Contents
Contents
4
Safety Instruction
5
Safety Instruction
6
Precautions before Use
7
Locating and Using Parts of the Controller Box
9
Front and Back of Control Box
9
Control Box Side
10
Installation
11
Attaching Controller to Table
11
Attaching Pedal Unit
11
Installing and Adjusting Knee Lifter Solenoid
12
Needle Bar Up/Down Stop Position Setting
12
Installing Program Unit
15
Sunstar Machine Installed with Program Unit
15
Wiring and Grounding
16
Specification of the Power Plug
16
Specification of Electric Current in Wiring of Power Plug
16
Names and Explanation of External Connector in Control Box
17
Changing Solenoid Supply Voltage (Basic Setting Values Upon Shipment: J19)
17
Setting Values of Solenoid Supply Voltage against Input Voltage (Input Voltage 220V Series)
17
Setting Values of Supplied Voltage to Solenoid against Input Voltage (Input Voltage: 110V)
18
Setting Supplied Voltage
18
Connection the Earth Wire of the Sewing Machine and Motor
19
Things to be Checked after Installation
19
Before the Power Is On...
19
After the Power Is On...
19
Program Unit Part Names and Method of Use
20
Installation
20
Method of Use: Start B/T Button
22
Method of Use: End B/T Button
22
Method of Use: the Needle Plate Position Selection Button When the Sewing Machine Stops
22
Method of Use: the Presser Foot-Lift Location Selection Button When the Sewing Machine Stops
23
Method of Use: Automatic Thread Trimmer and Wiper Selection Buttons
23
How to Use Product Counter and Bobbin Counter
23
Method of Use: Sewing Material Edge Sensor Selection Button
28
Method of Use: Pattern Work Selection Button
29
Method of Use: Constant Speed Sewing (AUTO) Selection Button
31
Method of Use: Sewing Speed Program Changing Button
31
Start and End Backtack Stitch Correction Method
32
Classification According to Backtack Sewing Condition
32
Start/End B/T Stitch Number Correction Method
33
When the Machine Sews Less than a Stitch more or Less than the One Programmed
34
Method of Use: Inertia Tuning Function
35
Sewing Machine Head Open Error and Safety Switch Error
35
How to Use the Edge Sensor (Fabric Edge Sensor)
36
Applicable Fortuna Model
36
Edge Sensor Program Setting
37
Edge Sensor Setting
37
Use of the Edge Sensor
38
Edge Sensor Deactivation
38
Edge Sensor Program Modification
39
Motor Controller Setting
40
Controller Setting by Machine Type
40
In Case Where the Top Thread Trimming Device Is Installed
41
Modification of the Sequence of Parameter B-55
41
Using the External Program Unit
41
How to Use the Imbedded Handy Controller
42
Trimming Sequence of Chain-Type Machine
43
Simple Operation Unit Part Names and Method of Use
44
Names of each Part in the Simple Operation Unit
44
Simple Program Unit Method of Use
44
Initializing
44
Programming the Start B/T Sewing Conditions with Button a
45
Programming the Start B/T Sewing Conditions with Button B
45
Programming the Needle Plate Position When Sewing Stops with Button C
45
Programming the Presser Foot-Lift Location When Sewing Stops with the Button D
46
Programming the Automatic Thread Trimmer and Wiper Movements with the Button E/Pro
46
Programming the Start and End B/T Stitches
46
Sewing Speed and Rotating Direction Programming Method
47
Method to Change Parameter Specific Items
47
Start and End B/T Stitch Number Correction Method
48
Method of Use of the Inertia Tuning Function
48
Fortuna Series Ė Full Function Software Method of Use
49
Basic Functions of the Fortuna Series 4 Full Function Software
49
Sewing Machine Up/Down Stop Location Automatic Recalling Function
49
Function Parameter
49
Fortuna Series 4 Full Function Software Specific Parameters
50
Group a Parameter: General Functions of Sewing Machine
50
Group B Parameter : All Types of Output, Full-On Time/Pwm Duty, Checking Input/Output Operations, Sewing Machine Models and Thread Trimming Sequence P
53
Group C Parameter: Pedal Acceleration/Deceleration Curve, Slow Starting Speed and Input/Output Port Change Related Parameter
57
Output PIN Function
58
Input PIN Function
59
Group D Parameter: All Types of Gain Parameter Related Motor Control
60
Method of Use and Explanations for Specific Items of the Parameter
61
Method of Use and Explanations for Specific Items of the Group a Parameter (General Functions of Sewing Machine)
61
Group B Parameter Specific Method of Use and Explanation
63
All Types of Output, Full-On Time/Pwm Duty Time Set up Method (All Types of Solenoids, LED and Signals)
63
B/T Stitch Correction Set up Method
63
Counter Function Method of Use
63
Group C Parameter Specifics Method of Use and Explanation
64
Pedal Stroke Step by Step Section and Speed Set up Method
64
Slow-Start Sewing Method of Use
64
Motor Maximum Speed Limit Set up Method
64
Thread Trimming Sequence Function Related Parameter Method of Use and Explanations (Full-Option)
65
Thread Trimming Sequence Function Method of Use (Items No. 54, 55, 56 of Group B)
65
Thread Trimming Sequence Selection Function Method of Use
66
Thread Trimming Sequence Automatic Change According to Sewing Machine Model Selection
66
Thread Trimming Sequence Function Related Parameter Method of Use and Explanations (Economic)
66
Changing the Trimming Sequence with the Simplified Operation Panel
66
Basic Structure of Thread Trimming Sequence Program Code
67
Thread Trimming Sequence Program Code List
68
Examples of the Function of Thread Trimming Sequence
71
Yamato Three-Needle Trimming
71
Timing of Thread Trimming Sequence
71
Flow Chart of Tread Trimming Sequence & Program Code
71
List of Codes by Machine Model
72
Breakdown and Troubleshooting
73
How to Place for Controller
74
Block Diagram
75
Parts Book
76
Motor Mechanism
78
Control Box Mechanism (Full Function Type)
79
Control Box Mechanism (Economic Type)
81
Program Unit Mechanism
83
Pedal Mechanism
85
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the SunStar Fortuna series and is the answer not in the manual?
Ask a question
SunStar Fortuna series Specifications
General
Brand
SunStar
Model
Fortuna series
Category
Engine
Language
English
Related product manuals
SunStar Fortuna 5 Series
107 pages
SunStar KM-235
107 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
