tBPC oCare Pro100 - User Manual

Questions and Answers

D
Denise StricklandAug 16, 2025
What to do if tBPC oCare Pro100 shows no PR/SpO2 value?
- A
  Angela KellyAug 16, 2025
  If the tBPC Medical Equipment doesn't display a PR/SpO2 value within 25 seconds, there might be a simple fix. First, if your wrist skin is cold, try warming or rubbing the application site to boost blood circulation. Ensure the device is positioned correctly, slightly above the wrist bone, fitting closely but comfortably. Excessive ambient light can interfere, so adjust the watchband for a snug fit and avoid bright light during measurement. Also, the measurement site should be free of tattoos or hair. Finally, check for any blood flow restrictions from things like arterial catheters or blood pressure cuffs and reduce or eliminate them.
B
brownnicoleAug 19, 2025
What to do if tBPC Medical Equipment displays a motion symbol?
- K
  kentheatherSep 12, 2025
  If the tBPC Medical Equipment displays a motion symbol, it means there is excessive movement during measurement. To resolve this, keep the lower arm wearing the device HORIZONTAL and STILL while taking the measurement.
H
Henry PopeAug 22, 2025
Why does the battery symbol flash on tBPC oCare Pro100 Medical Equipment?
- H
  harperraymondAug 22, 2025
  If the battery symbol is flashing on your tBPC Medical Equipment, it indicates that the battery is low. You should charge the device.
J
Joanna PenaAug 25, 2025
What to do if tBPC Medical Equipment shows a caution message?
- K
  Katherine AdamsAug 25, 2025
  If the tBPC Medical Equipment displays a caution message, this indicates a detected hardware malfunction. Press the ENTER buttons for 3 seconds to shut down the device. If the error message continues after you restart it, no answer.
M
michaeljamesAug 27, 2025
Why does tBPC Medical Equipment automatically shut down?
- J
  Jessica HernandezAug 28, 2025
  The tBPC Medical Equipment might automatically shut down because the battery is depleted. In this case, charge the device.
J
Jessica CrawfordAug 30, 2025
What to do if tBPC Medical Equipment is not responding?
- S
  Sharon NelsonAug 30, 2025
  If your tBPC Medical Equipment is not responding, it could be due to a software malfunction. Try pressing the SWITCH and ENTER buttons simultaneously for 10 seconds to reboot the device.
K
kterrellSep 2, 2025
Why does tBPC Medical Equipment battery run out quickly?
- D
  Danielle Garcia PhDSep 2, 2025
  If the battery on your tBPC Medical Equipment drains quickly, it may be because the Idle-Time-to-Sleep setting is set to “Never”. To conserve battery, change this setting to 3 minutes in the “SETTING” menu.
S
Stephen AndersenSep 4, 2025
What does it mean if the ALARM INDICATOR flashes YELLOW on tBPC Medical Equipment?
- J
  johnsteinSep 5, 2025
  If the ALARM INDICATOR on your tBPC Medical Equipment is flashing YELLOW, it signifies that a medium priority alarm has been triggered. You should address the patient condition immediately.
E
Elizabeth DavisSep 7, 2025
What does it mean if the ALARM INDICATOR flashes BLUE on tBPC Medical Equipment?
- K
  Kristen MeyerSep 7, 2025
  When the ALARM INDICATOR on the tBPC Medical Equipment flashes BLUE, it means a low priority alarm has been triggered. You should assess and address the device condition immediately.
T
Tiffany VargasSep 10, 2025
Why tBPC Medical Equipment can’t start continuous recording during measurement?
- B
  Brandi FloresSep 10, 2025
  If your tBPC Medical Equipment can’t start continuous recording during measurement, there are a few potential reasons: * The remaining battery may be less than 10%. If so, charge the battery fully before attempting continuous recording. * The device might be out of BLUETOOTH® range. Ensure the device is within approximately 10 meters (32.8 feet) of the paired device. * Radio frequency interference (like from a microwave) could be the issue. Try moving away from potential interference sources during the pairing process.

Summary

Trademarks and Regulatory Compliance

Trademarks and Copyright

Identifies the manufacturer (tBPC) and product names, along with copyright information.

FCC and NCC Compliance

Details device compliance with US FCC and Taiwan NCC regulations for radio frequency devices.

Safety Information

Safety Symbols and Labeling

Explains various standard safety symbols used on the device and in the manual for user guidance.

Warnings and Precautions

Provides critical safety warnings and cautions for proper and safe usage of the pulse oximeter.

Introduction and Device Overview

Intended Use and Introduction

Specifies the device's purpose, application, and target user.

Hardware Components

Describes the device's physical components, ports, and indicators.

Display Interface and Notations

Explains the device's screen interface, symbols, and notations for clear understanding.

Device Setup and Operation

Unpacking and Contents

Lists the standard kit contents and initial unpacking steps.

Battery Management

Information on battery life, charging status, and charging procedures.

Watchband Fitting and Wearing

Guides for adjusting and wearing the device correctly for optimal accuracy and comfort.

Startup and Mode Selection

Covers device power-on, self-tests, modes (Watch, Measurement), and basic functions.

Measurement and Settings

Measurement Procedures

Explains Spot-check and Continuous Monitoring measurement functions.

Device Controls and Menus

Navigating device menus for control, messages, and settings.

Alarm and Sleep Settings

Setting SpO2/PR alarm limits, brightness, and sleep timers.

Bluetooth Connectivity

Pairing, connecting, and transmitting data via Bluetooth.

Maintenance and Support

Care, Cleaning, and Storage

Instructions for cleaning and storing the device to ensure longevity.

Support and Warranty Information

Contact details for support and the product's warranty terms and conditions.

Troubleshooting

Troubleshooting Guide

Provides solutions for common problems and error messages encountered with the device.

Technical Specifications

Performance and Physical Specs

Detailed technical data on performance, system, electrical, and physical characteristics.

Electromagnetic Compatibility (EMC)

Manufacturer declaration and guidance on EMC, emissions, and immunity standards.

Parts and Accessories

Available Parts and Accessories

Lists available replacement parts and optional accessories for the device.

tBPC oCare Pro100 Specifications

General

Category	Medical Equipment
Type	Blood Pressure Monitor
Measurement Method	Oscillometric
Cuff Size	22-42cm
Memory Capacity	120 readings
Display	LCD
Product Name	oCare Pro100
Power Source	4 x AA batteries