Technogym Rotex 600 XTPRO - Page 6

ROTEX 600 XTPRO: Service & Maintenance Manual - rev. 1.1
Page ii
7.3. DISASSEMBLING THE CPU BOARD.................................................................................................................... 7.4
7.4. DISASSEMBLING THE KEYBOARD...................................................................................................................... 7.5
7.5. DISASSEMBLING THE CARDIO RECEIVER ...........................................................................................................7.6
7.6. DISASSEMBLING THE UPRIGHT GUARD..............................................................................................................7.7
7.7. DISASSEMBLING THE FRAME GUARDS...............................................................................................................7.8
7.8. DISASSEMBLING THE CENTER HANDLEBAR .......................................................................................................7.9
7.9. DISASSEMBLING THE SIDE HANDLEBARS.........................................................................................................7.10
7.10. DISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS....................................................................................... 7.11
7.11. DISASSEMBLING THE HS INTERFACE BOARD....................................................................................................7.12
7.12. DISASSEMBLING THE HAND SENSORS..............................................................................................................7.13
7.13. DISASSEMBLING THE ALTERNATOR.................................................................................................................7.14
7.14. DISASSEMBLING THE BELT.............................................................................................................................. 7.15
7.15. DISASSEMBLING THE REAR COVER ................................................................................................................. 7.16
7.16. DISASSEMBLING THE PEDAL LEVER GROUP..................................................................................................... 7.17
7.17. DISASSEMBLING THE PEDALS GROUP .............................................................................................................. 7.19
7.18. DISASSEMBLING THE PEDAL WHEEL TRACK ....................................................................................................7.20
7.19. DISASSEMBLING THE PEDAL WHEELS.............................................................................................................. 7.21
7.20. DISASSEMBLING THE FLYWHEELS ...................................................................................................................7.22
7.21. DISASSEMBLING THE ALTERNATOR BRUSHES ................................................................................................. 7.23
8. ADJUSTMENTS....................................................................................................................................................8.1
8.1. BELT ALIGNMENT .............................................................................................................................................8.1
8.2. BELT TENSION .................................................................................................................................................. 8.2
8.3. WEAR OF ALTERNATOR BRUSHES .....................................................................................................................8.3
9. CONFIGURING THE MACHINE ......................................................................................................................9.1
9.1. USER SETTING PARAMETERS.............................................................................................................................9.1
9.1.1. Language used .................................................................................................................................. 9.1
9.1.2. Measurement system .........................................................................................................................9.1
9.1.3. Maximum time................................................................................................................................... 9.2
9.1.4. Activating the “+” and “−” keys...................................................................................................... 9.2
9.1.5. Disabling the function keys...............................................................................................................9.2
9.1.6. Enabling the “ENTER” key .............................................................................................................. 9.3
9.1.7. Setting the priority ............................................................................................................................9.3
9.2. TECHNICAL SETTING PARAMETERS................................................................................................................... 9.3
9.2.1. Type of lever system .......................................................................................................................... 9.3
9.2.2. Enabling use of the hand sensor ....................................................................................................... 9.4
9.2.3. Enabling the display mode................................................................................................................9.4
9.3. MAINTENANCE INFORMATION .......................................................................................................................... 9.4
9.3.1. Hours on............................................................................................................................................ 9.4
9.3.2. Hours of use ...................................................................................................................................... 9.5
9.4. CHANGING THE MAINTENANCE INFORMATION ..................................................................................................9.5
9.4.1. Hours on............................................................................................................................................ 9.5
9.4.2. Hours of use ...................................................................................................................................... 9.5
10. SCHEDULED MAINTENANCE .......................................................................................................................10.1
10.1. EXTERNAL CLEANING OPERATIONS.................................................................................................................10.1
10.1.1. Setting up the operation ..................................................................................................................10.1
10.1.2. Cleaning operations ........................................................................................................................ 10.1
10.2. ROUTINE MAINTENANCE OPERATIONS ............................................................................................................ 10.2
10.2.1. Setting up the operation ..................................................................................................................10.2
10.2.2. Cleaning operations ........................................................................................................................ 10.2
10.3. SPECIAL MAINTENANCE OPERATIONS..............................................................................................................10.3
10.3.1. Setting up the operation ..................................................................................................................10.3
10.3.2. Checking the working conditions ....................................................................................................10.3
10.3.3. Checking the wiring and connections.............................................................................................. 10.3
10.3.4. Checking the display........................................................................................................................ 10.3
10.3.5. Checking the wear of the rubber handlebar cover .......................................................................... 10.3