Toro 41235 - User Manual

Questions and Answers:

B
Blake SimpsonSep 3, 2025
Why does a pressure drop occur when I turn on a boom on my Toro Paint Sprayer?
- E
  Edward OlsenSep 3, 2025
  If you experience a pressure drop when turning on a boom on your Toro Paint Sprayer, the boom bypass valve may be improperly adjusted; in this case, adjust the boom bypass valve. Also, there might be an obstruction in the boom valve body; remove the inlet and outlet connections to the boom valve and remove any obstructions. Finally, check for any missing nozzles and replace them if necessary.
T
Thomas GonzalezSep 18, 2025
Why is the monitor on my Toro 41235 Paint Sprayer operating erratically?
- B
  bsteeleSep 18, 2025
  If the monitor is operating erratically, a two-way radio may be too close to the monitor or its cables. Keep two-way radios away from the monitor and its cables.
D
Debra DeckerSep 1, 2025
Why is the speed always 0 or erratic on my Toro 41235 Paint Sprayer?
- T
  Tyler LivingstonSep 1, 2025
  If the speed reading is always 0 or erratic on your Toro Paint Sprayer, ensure the monitor cable is securely connected. If that doesn't solve the issue, calibrate the speed sensor. If problems continue, the speed sensor may be damaged, and you should contact your Authorized Service Dealer.
J
James ColemanSep 23, 2025
What to do if the monitor does not function on my Toro Paint Sprayer?
- B
  Barbara FosterSep 23, 2025
  If the monitor isn't working, start by checking the monitor cable to ensure it's properly connected. If the issue persists, the monitor or cable might be damaged.
J
Justin MaldonadoSep 22, 2025
What to do if a pressure drop occurs when I turn on a boom on my Toro 41235 Paint Sprayer?
- R
  ryan84Sep 22, 2025
  A pressure drop when turning on a boom could be due to several reasons. First, check the boom bypass valve to ensure it's properly adjusted. Also, inspect the boom valve body for any obstructions and remove them. Finally, check if any nozzles are missing and replace them if needed.
L
Lisa KlineAug 29, 2025
Why is my Toro Paint Sprayer monitor erratic?
- M
  Madison HinesAug 29, 2025
  If your Toro Paint Sprayer monitor is operating erratically, it might be due to interference from a two-way radio being too close to the monitor or its cables. To resolve this, simply keep two-way radios away from the monitor and its cables.
J
Jennifer SuttonAug 28, 2025
What to do if a boom valve is leaking on my Toro 41235?
- K
  Kevin JohnsonAug 28, 2025
  If a boom valve is leaking, it's likely due to a deteriorated O-ring. Stop the spray system and pump, and turn off the sprayer. Disassemble the valve and replace the O-rings.
D
Debbie RivasAug 27, 2025
How to fix a boom section that does not spray on my Toro 41235?
- E
  Eric FoleyAug 27, 2025
  If a boom section isn't spraying, it could be due to a few reasons. First, check for any pinched hoses and repair or replace them. Also, make sure the boom bypass valves are properly adjusted.
M
Meghan BarberAug 26, 2025
How do I correct an inaccurate distance measurement on my Toro Paint Sprayer?
- C
  Christopher PittmanAug 27, 2025
  If the distance measurement is inaccurate, calibrate the speed sensor, as it may not be calibrated correctly.
N
Nicholas ChungAug 25, 2025
What to do if the total volume is inaccurate on my Toro 41235?
- R
  Russell JimenezAug 26, 2025
  If the total volume displayed is inaccurate, it might be because the flow meter is dirty or clogged, so you should clean the flow meter. Another possible cause is that the flow meter isn't calibrated correctly, so you should calibrate the flow meter.