© 2005 - 2007 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO520/523/600/603/720/723/850/853
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 7
2
E752 RADF jam Original not reaching original intermediate transport
sensor: The leading edge of the original which has
passed the read sensor does not reach the original
intermediate transport sensor.
Ch.5.1.4
E761 Original remaining at original length detection sen-
sor
Ch.5.1.4
E762 Original remaining at original registration sensor Ch.5.1.4
E763 Original remaining at original width detection sen-
sor
Ch.5.1.4
E764 Original remaining at read sensor Ch.5.1.4
E765 Original remaining at original intermediate transport
sensor
Ch.5.1.4
E766 Original remaining at small original reverse sensor Ch.5.1.4
E767 Original remaining at small original exit sensor Ch.5.1.4
E768 Original remaining at large original exit sensor Ch.5.1.4
E800 24 VDC supply off jam: A job is started or continued
while 24 VDC supply is shut off.
Ch.5.1.4
E860 Jam access cover open jam: The jam access cover
has opened during the operation of the RADF.
Ch.5.1.4
E870 RADF open jam: The RADF has opened during the
operation of the RADF.
Ch.5.1.4
E9F0 Finisher jam
(Puncher section)
Hole punch jam: Hole punching is not performed
properly.
Ch.5.1.5 [ 1 ]
EA10 Finisher jam
(Finisher section)
Paper transport delay jam: Paper which has passed
the exit sensor does not reach the inlet sensor.
Ch.5.1.5 [ 2 ]
EA20 Paper transport stop jam: Paper which has reached
the inlet sensor does not pass the inlet sensor.
Ch.5.1.5 [ 2 ]
EA30 Power-ON jam: Paper is remaining at the inlet sen-
sor when the power is turned ON.
Ch.5.1.5 [ 2 ]
EA40 Door open jam: The upper cover or the front cover
of the Finisher has opened, or the upper door or the
front door of the Hole Punch Unit has opened dur-
ing printing.
Ch.5.1.5 [ 2 ]
EA50 Stapling jam: Stapling is not performed properly. Ch.5.1.5 [ 2 ]
EA60 Early arrival jam: The inlet sensor detects paper
earlier than the specified timing.
Ch.5.1.5 [ 2 ]
EA80 Finisher jam
(Saddle Stitcher sec-
tion)
Stapling jam: Stapling is not performed properly. Ch.5.1.5 [ 3 ]
EA90 Door open jam: The delivery cover or the inlet cover
has opened during printing.
Ch.5.1.5 [ 3 ]
EAA0 Power-ON jam: Paper is remaining at the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper sen-
sor, vertical path paper sensor or delivery sensor
when the power is turned ON.
Ch.5.1.5 [ 3 ]
EAB0 Paper transport stop jam: Paper which has passed
the inlet sensor does not reach or pass the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper sen-
sor or delivery sensor.
Ch.5.1.5 [ 3 ]
EAC0 Transport delay jam: Paper which has reached the
inlet sensor does not pass the inlet sensor.
Ch.5.1.5 [ 3 ]
EAD0 Other paper jam Print end command time-out jam: The printing has
not finished normally due to the communication
error between the SYS board and LGC board at the
end of the printing.
Ch.5.1.5 [ 5 ]
Error code Classification Contents Troubleshooting
To Next Page
Loading...
