K-17
E6581386
11
[22] Communication function Sensorless vector/PG feedback control (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Constant
Reference
0576 IP address setting method
0: Manual setting (~ Enabled)
1: BOOTP
2: DHCP
1/1 0 Enabled ●/● ● ● *1
0577 Data1
0~255 1/1 0 Enabled ●/● ● ● *1
0578 Data2 0~255 1/1 0 Enabled ●/● ● ● *1
0579 Data3 0~255 1/1 0 Enabled ●/● ● ● *1
0580
IP card
Data4 0~255 1/1 0 Enabled ●/● ● ● *1
0581 Data1
0~255 1/1 0 Enabled ●/● ● ● *1
0582 Data2 0~255 1/1 0 Enabled ●/● ● ● *1
0583 Data3 0~255 1/1 0 Enabled ●/● ● ● *1
0584
Subnet mask
Data4 0~255 1/1 0 Enabled ●/● ● ● *1
0585 Data1
0~255 1/1 0 Enabled ●/● ● ● *1
0586 Data2 0~255 1/1 0 Enabled ●/● ● ● *1
0587 Data3 0~255 1/1 0 Enabled ●/● ● ● *1
0588
IP gate1
Data4 0~255 1/1 0 Enabled ●/● ● ● *1
0589 Data1
0~255 1/1 0 Enabled ●/● ● ● *1
0590 Data2 0~255 1/1 0 Enabled ●/● ● ● *1
0591 Data3 0~255 1/1 0 Enabled ●/● ● ● *1
0592
IP master
Data4 0~255 1/1 0 Enabled ●/● ● ● *1
0593 IO scan permission
0: Prohibit
1: Permit
1/1 0 Enabled ●/● ● ● *1
0594
Communication time-out (Modbus)
0.0~60.0sec. 0.1/0.1 0 Enabled ●/● ● ● *1
*1:This function is for Etherenet communication option.(planning)
[23] Protection functions [1/4] Sensorless vector/PG feedback control (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Constant
Reference
0601 Stall prevention level 10~164%, 165:Deactivated 1/1 120 Enabled ●/● ● ● 6. 26. 1
0602 Inverter trip record retention selection
0:Clear when power is turned off
1:Retain even after power is turned off
1/1 0 Enabled ●/● ● ● 6. 26. 2
0603 Emergency stop
0:Coast stop
1:Deceleration stop
2:Emergency DC braking
1/1 0 Disabled ●/● ● ● 6. 26. 3
0604 Emergency DC braking control time 0.0~20.0 sec. 0.1/0.1 1.0 Enabled ●/● ● ● 6. 26. 3
0605
Output phase failure detection mode
selection
0:Deselect
1:At starting (only one time after power is turned
on)
2:At starting (each time power is turned on)
3:During operation
4:At starting + during operation
5:Output cut-off detection enabled
1/1 0 Disabled ●/● ● ● 6. 26. 4