Toshiba VF-PS1 - Page 258

K-16
E6581386
11
[20] Adjustment parameters Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Constant
Reference
 0460 Speed loop proportional gain 1~9999 1/1 12 Enabled ●/● -- *1  0461 Speed loop stabilization coefficient 1~9999 1/1 100 Enabled ●/● -- *1  0462 Moment of inertia of load 1 0~100 1/1 35 Enabled ●/●● -*1  0470 VI/II input bias 0~255 1/1 *2 Enabled ●/●●●6. 23  0471 VI/II input gain 0~255 1/1 *2 Enabled ●/●●●6. 23  0472 RR/S4 input bias 0~255 1/1 *2 Enabled ●/●●●6. 23  0473 RR/S4 input gain 0~255 1/1 *2 Enabled ●/●●●6. 23  0474 RX input bias 0~255 1/1 *2 Enabled ●/●●●6. 23  0475 RX input gain 0~255 1/1 *2 Enabled ●/●●●6. 23  0476 Optional AI1 input bias 0~255 1/1 *2 Enabled ●/●●●6. 23  0477 Optional AI1 input gain 0~255 1/1 *2 Enabled ●/●●●6. 23  0478 Optional AI2 input bias 0~255 1/1 *2 Enabled ●/●●●6. 23  0479 Optional AI2 input gain 0~255 1/1 *2 Enabled ●/●●●6. 23  0498 PM motor constant 1 (d axis inductance) 0~25% 0.1/0.1 10.0 Disabled - ● -6. 24  0499 PM motor constant 2 (q axis inductance) 0~25% 0.1/0.1 10.0 Disabled - ● -6. 24
*1: ⇒ For details, refer to Instruction Manual (E6581333) specified in Section 6.36. *2: ⇒ Settings vary from unit to unit. Even if  is set to , no change is made to these values.
[21] Acceleration/deceleration 2 Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Constant
Reference
 0500 Acceleration time 2 0.1~6000 sec. 0.1/0.1 *2 *1 Enabled ●/●●●6. 25. 1  0501 Deceleration time 2 0.1~6000 sec. 0.1/0.1 *2 *1 Enabled ●/●●●6. 25. 1  0502 Acceleration/deceleration 1 pattern
0:Straight 1:S-pattern 1 2:S-pattern 2
1/1 0 Enabled ●/●●●6. 25. 1
 0503 Acceleration/deceleration 2 pattern
0:Straight 1:S-pattern 1 2:S-pattern 2
1/1 0 Enabled ●/●●●6. 25. 1
 0504 Panel acceleration/deceleration selection
1:Acceleration/deceleration 1 2:Acceleration/deceleration 2
1/1 １ Enabled ●/●●●6. 25. 1
 0505
Acceleration/deceleration switching frequency
0.0~ Hz 0. 1/0.01 0.0 Enabled ●/●●●6. 25. 1
*1: Default values vary depending on the capacity. ⇒ See the table of K-41. *2: Changing the parameter  enables to set to 0.01 sec. (adjustment range: 0.01~600.0 sec.).