K-24
E6581386
11
[26] Communication function [1/4] Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
Minimum
setting unit
(Panel/Communi
cation)
Default
setting
Write during
running
Vector
control
PM
control
V/f Constant
Reference
0800 Communication speed (2-wire RS485)
0:9600 bps
1:19200 bps
2:38400 bps
1/1 1 Enabled ●/●●●6. 34. 1
0801
Parity (common to 2-wire RS485 and 4-wire
RS485)
0:Non parity
1:Even parity,
2:Odd parity
1/1 1 Enabled ●/●●●6. 34. 1
0802 Inverter number (common) 0~247 1/1 0 Enabled ●/●●●6. 34. 1
0803
Communications time-out time (common to
2-wire RS485 and 4-wire RS485)
0:OFF, 1~100 sec. 1/1 0 Enabled ●/●●●6. 34. 1
0804
Communications time-out action (common
to 2-wire RS485 and 4-wire RS485)
0~8 1/1 8 Enabled ●/●●●6. 34. 1
0805 Send waiting time (2-wire RS485) 0.00:Default, 0.01~2.00 sec. 0.01/0.01 0.00 Enabled ●/●●●6. 34. 1
0806
Master/slave setting for inverter-to-inverter
communications (2-wire RS485)
0:Slave (issues a 0Hz command if something
goes wrong with the master)
1:Slave (continues operation if something goes
wrong with the master)
2:Slave (trips for emergency stop if something
goes wrong with the master)
3:Master (sends a frequency command)
4:Master (sends an output frequency)
5. -
6. -
1/1 0 Enabled ●/●●●6. 34. 1
0807 Protocol selection (2-wire RS485)
0:TOSHIBA
1:MODBUS
1/1 0 Enabled ●/●●●6. 34. 1
0810 Frequency point selection
0:Disabled
1:2-wire RS485
2:4-wire RS485
3:Communication add option
1/1 0 Enabled ●/●●●6. 34. 1
0811 Point 1 setting 0-100% 1/1 0
Enabled *2
●/●●●6. 34. 1
0812 Point 1 frequency 0.0~ Hz 0.1/0.01 0.0
Enabled *2
●/●●●6. 34. 1
0813 Point 2 setting 0~100% 1/1 100
Enabled *2
●/●●●6. 34. 1
0814 Point 2 frequency 0.0~ Hz 0.1/0.01 *1
Enabled *2
●/●●●6. 34. 1
0820 Communication speed (4-wire RS485)
0:9600 bps
1:19200 bps
2:38400 bps
1/1 1 Enabled ●/●●●6. 34. 1
0825 Send waiting time (4-wire RS485) 0.00:Default, 0.01~2.00 sec. 0.01/0.01 0.00 Enabled ●/●●●6. 34. 1
*1: Inverter with a model number ending with -WN: 60.0 -WP: 50.0
*2: Effective when a command value is sent by communication.
To Next Page
Loading...
