TSC TX200 Series User Manual (English)

Other manuals for TSC TX200 Series

Questions and Answers:

T
Thomas MathisAug 29, 2025
How to fix poor print quality on TSC Barcode Reader?
- S
  Shirley FritzAug 29, 2025
  Poor print quality on your TSC Barcode Reader can occur due to several reasons: * The ribbon and media might be loaded incorrectly. Reload the supply. * There might be dust or adhesive on the print head. Clean the print head. * The print density might not be set properly. Adjust the print density and print speed. * The printhead element could be damaged. Run a printer self-test to check the print head test pattern for missing dots. * The ribbon and media might be incompatible. Change to a proper ribbon or label media. * The printhead pressure might not be set correctly or the print head mechanism does not latch properly.
J
Juan ColemanAug 29, 2025
Why is my TSC printer missing printing on the left or right side of the label?
- L
  Laura LopezAug 29, 2025
  If your TSC printer is missing printing on the sides of the label, it's likely due to an incorrect label size setup. Set the correct label size in your printer settings.
M
michelleespinozaAug 28, 2025
Why is my TSC TX200 showing 'Other errors' (LED turn on)?
- J
  James DixonAug 28, 2025
  If your TSC printer shows 'Other errors', it could be due to several reasons: * Out of memory: Delete unused files in the FLASH/DRAM. * Print head overheat: Wait for the print head to cool down. * Cutter error/jam: Remove any stuck labels inside the cutter module.
J
jamescisnerosAug 27, 2025
What to do if my TSC TX200 shows 'No Ribbon'?
- S
  Shelley RomeroAug 27, 2025
  If your TSC printer indicates 'No Ribbon', it could be due to running out of ribbon. Supply a new ribbon roll. Alternatively, the ribbon may be installed incorrectly; refer to section 3.2 for re-installation steps.
R
Rebecca TravisAug 27, 2025
How to fix irregular printing on TSC printer?
- C
  Courtney SweeneyAug 27, 2025
  If your TSC printer is printing irregularly, it may be in Hex Dump mode. Turn the printer off and on to exit this mode. Also, check and reset the RS-232 setting.
D
Daniel Powell IIIAug 26, 2025
Why is there no print on the label from my TSC printer?
- M
  Mary GoldenAug 26, 2025
  If your TSC printer is producing blank labels, ensure that the label and ribbon are loaded correctly according to the instructions. Verify that the ribbon and media are compatible, paying attention to the ribbon-inked side. Also, consider cleaning the print head.
A
Alicia TrevinoAug 25, 2025
How to resolve 'No Paper' error on my TSC printer?
- A
  Amanda BatesAug 26, 2025
  If your TSC printer shows a 'No Paper' error, first ensure that you have a new label roll. If the roll is new, make sure the label roll is correctly installed. You might also need to calibrate the gap/black mark sensor.
J
James JamesAug 25, 2025
How to fix poor print quality on my TSC printer?
- M
  Michael CabreraAug 25, 2025
  To improve the print quality of your TSC printer, try the following: * Reload the ribbon and media. * Clean the print head to remove any dust or adhesive. * Adjust the print density and print speed. * Run a self-test to check for damage to the print head element. * Ensure you are using compatible ribbon and label media.

TSC TX200 Series Specifications

General

Operating Temperature	41°F to 104°F (5°C to 40°C)
Print Method	Thermal Transfer / Direct Thermal
Resolution	203 dpi
Memory	8 MB Flash
Processor	32-bit RISC
Communication Interface	USB 2.0
Core Diameter	1" (25.4 mm)
Power Supply	100-240 VAC, 50/60 Hz
Storage Temperature	-4°F to 122°F (-20°C to 50°C)
Certifications	CE, FCC, RoHS, UL, TUV, CB, CCC
Operating Humidity	25-85% non-condensing