What causes missing printing on the left or right side of TSC Barcode Reader label?
Missing print on the sides of labels from your TSC Barcode Reader is caused by: * Wrong label size setup. Set the correct label size.
How to fix poor print quality on my TSC printer?
To improve the print quality of your TSC printer, try the following: * Reload the ribbon and media. * Clean the print head to remove any dust or adhesive. * Adjust the print density and print speed. * Run a self-test to check for damage to the print head element. * Ensure you are using compatible ribbon and label media.
How to resolve 'No Paper' error on my TSC printer?
If your TSC printer shows a 'No Paper' error, first ensure that you have a new label roll. If the roll is new, make sure the label roll is correctly installed. You might also need to calibrate the gap/black mark sensor.
Why is there no print on the label from my TSC printer?
If your TSC printer is producing blank labels, ensure that the label and ribbon are loaded correctly according to the instructions. Verify that the ribbon and media are compatible, paying attention to the ribbon-inked side. Also, consider cleaning the print head.
How to fix irregular printing on TSC printer?
If your TSC printer is printing irregularly, it may be in Hex Dump mode. Turn the printer off and on to exit this mode. Also, check and reset the RS-232 setting.
What to do if my TSC TX200 shows 'No Ribbon'?
If your TSC printer indicates 'No Ribbon', it could be due to running out of ribbon. Supply a new ribbon roll. Alternatively, the ribbon may be installed incorrectly; refer to section 3.2 for re-installation steps.
Why is my TSC TX200 showing 'Other errors' (LED turn on)?
If your TSC printer shows 'Other errors', it could be due to several reasons: * Out of memory: Delete unused files in the FLASH/DRAM. * Print head overheat: Wait for the print head to cool down. * Cutter error/jam: Remove any stuck labels inside the cutter module.
Why is my TSC printer missing printing on the left or right side of the label?
If your TSC printer is missing printing on the sides of the label, it's likely due to an incorrect label size setup. Set the correct label size in your printer settings.
How to fix poor print quality on TSC Barcode Reader?
Poor print quality on your TSC Barcode Reader can occur due to several reasons: * The ribbon and media might be loaded incorrectly. Reload the supply. * There might be dust or adhesive on the print head. Clean the print head. * The print density might not be set properly. Adjust the print density and print speed. * The printhead element could be damaged. Run a printer self-test to check the print head test pattern for missing dots. * The ribbon and media might be incompatible. Change to a proper ribbon or label media. * The printhead pressure might not be set correctly or the print head mechanism does not latch properly.
What to do if my TSC Barcode Reader is continuously feeding labels?
If your TSC Barcode Reader is continuously feeding labels, it could be due to: * An incorrect printer setting. Initialize the printer and perform gap/black mark calibration. * Improper gap/black mark sensor sensitivity. Calibrate the gap/black mark sensor. * Incorrect label size setting. Ensure the label size is set correctly in the labeling software or program. * Labels stuck inside the printer mechanism near the sensor area. Remove any stuck labels.
General| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
|---|---|
| Print Method | Thermal Transfer / Direct Thermal |
| Resolution | 203 dpi |
| Memory | 8 MB Flash |
| Processor | 32-bit RISC |
| Communication Interface | USB 2.0 |
| Core Diameter | 1" (25.4 mm) |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Storage Temperature | -4°F to 122°F (-20°C to 50°C) |
| Certifications | CE, FCC, RoHS, UL, TUV, CB, CCC |
| Operating Humidity | 25-85% non-condensing |
Details the standard hardware and software features of the printer.
Explains LED indicators, feed/pause button functions, and status meanings.
Step-by-step guide for placing, connecting, and powering on the printer.
Details the various functions available within the diagnostic tool for printer setup.
Instructions for configuring Ethernet using USB, RS-232, or direct Ethernet interfaces.
Procedures for calibrating ribbon and gap/black mark sensors.
Details sensor calibration, self-test printing, and dump mode functions.
Restores printer settings to factory defaults, clearing memory.
Access to diagnostic functions like Print Config, Dump Mode, and Print Head checks.
To Next Page
