Vacon 20 - Page 75

To Next Page

To Previous Page

control panel vacon

•

Note! Fault History can be reset by long pressing the BACK / RESET

button for 5 second time,when the API is in fault history sub-

menu level (F6.x), it will also clear all active faults.

See Chapter 5 for fault descriptions.

Main Page

Table of Contents3
Safety7
Warnings7
Safety Instructions9
Earthing and Earth Fault Protection9
Before Running the Motor11
Receipt of Delivery13
Type Designation Code13
Storage13
Maintenance14
1Capacitor Recharge14
Warranty15
Manufacturer's Declaration of Conformity16
Installation17
Mechanical Installation17
1Vacon 20 Dimensions21
2Cooling25
3Power Losses26
4EMC Levels33
5Changing the EMC Protection Class from C2 or C3 to C434
Cabling and Connections36
1Power Cabling36
2Control Cabling38
3Allowed Option Boards in Vacon2042
4Screw of Cables44
5Cable and Fuse Specifications46
6General Cabling Rules49
7Stripping Lengths of Motor and Mains Cables50
8Cable Installation and the UL Standards50
9Cable and Motor Insulation Checks50
Commissioning53
Commissioning Steps of Vacon53
Fault Tracing55
Vacon 20 Application Interface59
Introduction59
Control I / O61
Control Panel63
General63
Display63
Keypad64
Navigation on the Vacon 20 Control Panel66
1Main Menu66
2Reference Menu67
3Monitoring Menu68
4Parameter Menu72
5System Menu74
STANDARD Application Parameters77
Quick Setup Parameters (Virtual Menu, Shows When Par. 17.2 = 1)78
Motor Settings (Control Panel: Menu PAR -> P1)80
Start / Stop Setup (Control Panel: Menu PAR -> P2)82
Frequency References (Control Panel: Menu PAR -> P3)83
Ramps and Brakes Setup (Control Panel: Menu PAR -> P4)84
Digital Inputs (Control Panel: Menu PAR -> P5)86
Analogue Inputs (Control Panel: Menu PAR -> P6)87
Pulse Train / Encoder (Control Panel: Menu PAR -> P7)87
Digital Outputs (Control Panel: Menu PAR -> P8)88
Analogue Outputs (Control Panel: Menu PAR -> P9)90
Fieldbus Data-Mapping (Control Panel: Menu PAR -> P10)91
Prohibited Frequencies (Control Panel: Menu PAR -> P11)92
Limit Supervisions (Control Panel: Menu PAR -> P12)93
Protections (Control Panel: Menu PAR -> P13)94
Fault Autoreset Parameters (Control Panel: Menu PAR -> P14)96
PID Control Parameters (Control Panel: Menu PAR -> P15)96
Motor Pre-Heat (Control Panel: Menu PAR -> P16)99
Easy Usage Menu (Control Panel: Menu PAR -> P17)99
System Parameters100
Parameter Descriptions105
Motor Settings (Control Panel: Menu PAR -> P1)105
Start / Stop Setup (Control Panel: Menu PAR -> P2)110
Frequency References (Control Panel: Menu PAR -> P3)118
Ramps & Brakes Setup (Control Panel: Menu PAR -> P4)120
Digital Inputs (Control Panel: Menu PAR -> P5)125
Analogue Inputs (Control Panel: Menu PAR -> P6)126
Pulse Train / Encoder (Control Panel: Menu PAR -> P7)127
Digital Outputs (Control Panel: Menu PAR -> P8)128
Analogue Outputs (Control Panel: Menu PAR -> P9)129
Fieldbus Data-Mapping (Control Panel: Menu PAR -> P10)130
Prohibited Frequencies (Control Panel: Menu PAR -> P11)131
Protections (Control Panel:menu Par->P13)132
Automatic Reset (Control Panel: Menu PAR -> P14)139
PID Control Parameters (Control Panel: Menu PAR -> P15)140
Application Setting (Control Panel: Menu PAR->P17)143
System Parameter145
Modbus RTU147
1Termination Resistor147
2Modbus Address Area147
3Modbus Process Data148
Technical Data153
Vacon 20 Technical Data153
Power Ratings155
1Vacon 20 - Mains Voltage 208-240 V155
2Vacon 20 - Mains Voltage 115 V156
3Vacon 20 - Mains Voltage 380-480 V156
4Vacon 20 - Mains Voltage 600 V157
Brake Resistors157

Vacon 20 - Page 75

Table of Contents

Other manuals for Vacon 20

Related product manuals