To Next PageTo Next Page
How to resolve document feeder jams in Xerox WorkCentre 5330 All in One Printer?
Document feeder jams in your Xerox All in One Printer can occur due to: * Unsupported media. Use only Xerox-approved media. * Exceeding the document feeder's capacity. Place fewer documents in the feeder. * Improperly adjusted document feeder guides. Ensure the media guides fit snugly against the media.
What causes duplex unit jams on Xerox WorkCentre 5330?
Duplex unit jams on your Xerox All in One Printer can be caused by using unsupported media of the wrong size, thickness, or type. Use only Xerox-approved media. Also, recheck the media path inside the duplex module, remove any jammed paper, ensure you have not mixed media types in the tray, and avoid printing envelopes, labels, or extra heavyweight paper 2-sided.
What to do if paper jam message stays on Xerox WorkCentre 5330 All in One Printer?
If the paper jam message persists on your Xerox All in One Printer, it indicates that some paper remains jammed inside the printer. Recheck the media path and ensure that all jammed paper has been removed.
What to do if my Xerox WorkCentre 5330 does not turn on?
If your Xerox All in One Printer doesn't turn on, there are several potential causes: * The power switch may not be correctly turned on. Ensure the main power switch behind the front cover is on, and turn off the printer using the power switch on the lower center tray, wait two minutes, and then turn it back on. * The power cord might not be securely plugged into the outlet. Turn off the printer and plug the power cord securely into the outlet. * The outlet itself may have an issue. Plug another electrical appliance into the outlet to see if it operates properly. Try a different outlet. * The printer might be connected to an outlet with incorrect voltage or frequency. Use a power source with the correct specifications.
Why is printing taking so long on my Xerox WorkCentre 5330?
Several factors can cause slow printing on your Xerox All in One Printer: * The printer may be set to a slower printing mode for special media. Ensure the media type is correctly set in the print driver and at the printer control panel, as printing with special media takes more time. * The printer could be in power saving mode, which requires time to start printing. * The print job might be very complex. In this case, simply wait for the job to complete.
How to fix media misfeeds on Xerox WorkCentre 5330?
If your Xerox All in One Printer is experiencing media misfeeds, consider the following: * Ensure the media is correctly positioned in the tray and that the media guides are properly set. * If there are too many sheets in the tray, remove the excess paper and load it below the fill line. * Adjust the media guides to match the size of the media. * If the media is warped or wrinkled, remove it, smooth it out, and reload it. If it continues to misfeed, use different media. * Replace moist media with new, dry media. * Make sure you are using Xerox-approved media. * Ensure label sheets are loaded according to the manufacturer’s instructions. * When using Tray 5 (Bypass Tray) for envelopes, load them facedown with the flaps closed, on the leading edge.
Why does my Xerox WorkCentre 5330 All in One Printer pull multiple sheets together?
Your Xerox All in One Printer might pull multiple sheets together due to: * An overfilled paper tray. Remove some paper, ensuring not to load past the fill line. * Uneven front edges of the paper. Remove the media, align the front edges, and reload. * Moist media due to humidity. Replace the media with new, dry media. * Too much static electricity. Try a new ream of paper. * Unsupported media. Use only Xerox-approved media.
What to do if Xerox All in One Printer is making unusual noises?
Unusual noises from your Xerox All in One Printer can stem from: * An incorrectly installed tray. Open and close the tray you are printing from. * An obstruction or debris inside the printer. Turn off the printer and remove any obstruction or debris. If you cannot remove it, contact your Xerox representative.
How to solve 2-sided printing problems on Xerox WorkCentre 5330?
Two-sided printing issues on your Xerox All in One Printer may arise if the media or settings are incorrect. Ensure you are using the correct media. Envelopes, labels, gloss, and extra heavyweight stock are not suitable for 2-sided printing. In the print driver, select the 2-Sided Printing option.
What to do for scanner error on Xerox WorkCentre 5330?
If you encounter a scanner error on your Xerox All in One Printer, it could be due to the scanner not communicating. Turn off the printer using the power switch on the lower center tray, wait two minutes, and then turn the printer back on. If the problem persists, contact your local Xerox Representative.
General| Print Technology | Laser |
|---|---|
| Functions | Print, Copy, Scan, Fax |
| Print Speed | Up to 30 ppm |
| Print Resolution | Up to 1200 x 1200 dpi |
| Copy Resolution | Up to 600 x 600 dpi |
| Scan Resolution | Up to 600 x 600 dpi |
| Hard Drive | 80 GB |
| Copy Speed | Up to 30 cpm |
| Operating System Compatibility | Windows, Mac, Linux |
| Connectivity | USB 2.0 |
| Paper Sizes | A4, A5, B5 |
| Scan Destinations | Scan to Email, Network, USB |
| Fax Speed | 33.6 kbps |
| Duplex Printing | Automatic |
Safety guidelines for electrical connections and usage.
Safety precautions during printer maintenance procedures.
Details on available hardware configurations and standard features.
Description and layout of the printer's touch screen control panel.
Instructions for connecting the printer to power and the network.
Steps to power on the printer using its main and secondary switches.
Procedures for properly shutting down the printer.
Steps for installing printer drivers and utilities for various OS.
Information on compatible paper types, weights, and sizes for printing.
How to modify copy settings like reduction, enlargement, and image quality.
How to save scanned documents to a folder on the printer's hard drive.
Adjusting scan settings such as color, resolution, and file format.
Steps for sending faxes using the printer's embedded fax feature.
How to send faxes directly from your computer using the print driver.
How to adjust fax settings like resolution, original type, and 2-sided faxing.
General guidelines and procedures for cleaning printer components.
Common printer issues and their solutions, including restart procedures.
Step-by-step instructions for removing paper jams from various printer locations.
