What to do if the Xylem Controller pump does not snore during sump cleaning?
If the pump doesn't snore during sump cleaning and stops at the stop level, verify that the start and stop level is greater than 10% of the range and check the sensor scaling.
Why are the energy frequencies different for two Xylem SmartRun® Controllers in the same installation?
If the energy frequencies and pump down times differ significantly between two SmartRun® units in the same setup, inspect the mechanical and hydraulic condition of the pumps. Ensure the pump sits correctly on the discharge connection or that a flush valve closes properly. Adjust using the P4-14:Max freq start run time parameter.
What to do if the Xylem Controller fitted communication module has a fault (Fault code 52)?
If the fitted communication module has a fault, check that the module is correctly inserted.
What to do if the Xylem Controller I/O card communications trip (Fault code 53)?
If there is an I/O card communications trip, check that the module is correctly inserted.
General| Brand | Xylem |
|---|---|
| Model | FLYGT SmartRun SRC 311 |
| Category | Controller |
| Language | English |
Overview of manual purpose and user guidance.
Essential safety precautions and hazard warnings.
Explains safety symbols and terms.
Details hazard levels and electrical safety precautions.
General safety guidelines and warranty information.
Warranty exclusions, liability, and required personnel qualifications.
Inspecting delivery/unit and safe lifting practices.
General guidelines and precautions for transporting the unit.
Recommendations and requirements for product storage.
Overview of SRC 311, Experior concept, and software version.
Identifies and illustrates the main components of the drive units.
Details LED indicators, alarm outputs, and Hand-0-Auto switch.
Discusses remote monitoring, protocols, and data plate details.
Explains model number structure and de-rating procedures.
Covers explosive zones, environment, altitude, and temperature requirements.
Detailed dimensions for IP20 frame sizes.
Required clearance for IP20 mounting.
Detailed dimensions for IP55 frame sizes.
Detailed dimensions for IP66 frame sizes.
Required clearances for IP55 and IP66 mounting.
Instructions for installing level sensors.
Illustrates sensor placement and levels.
Safety, general installation, and power supply requirements.
Details requirements for fuses, cables, and grounding.
Covers EMC, capacitor discharge, and UL compliance ratings.
Specifies torque values and requirements for system installation.
Instructions for installing a two-pump system.
Connecting power cables for a two-pump system.
Connecting control and sensor leads for a two-pump system.
Continues wiring instructions for two-pump systems.
Connecting shared sensor signals.
Provides terminal diagrams for pump systems.
Lists terminal functions for power and control I/O.
Terminal functions for extension cards and three-pump system installation.
Steps for optional modules and relay contact wiring.
Identifies display symbols, names, and descriptions of buttons.
Explains various drive operating modes.
Continues explanation of operating modes.
Lists IP20 display messages and initial drive setup.
Details parameter settings for start-up, including levels.
Instructions for changing display language and basic pump control.
Details high inflow and energy minimizer functions.
Explains alternation schemes and pump block functionality.
Specifics for pump block and overview of cleaning functions.
Details Blockage, Partial clogging, Flush valve, Sump cleaning.
Details Pipe cleaning, Maintenance run, High-level runtime, Water hammer reduction.
Covers optional module functions and accessing extended parameters.
Instructions for resetting the drive to factory defaults.
Continues factory reset instructions.
Importance of ground tests and preventive measures.
Details inspection of fans, capacitors, and other components.
Safety for troubleshooting and overview of alarm functions.
Lists common symptoms and alarm types with actions.
Explains alarm log, state, and communication.
Procedures for resetting alarms and reference to fault codes.
Continues listing fault codes and corrective actions.
Continues listing fault codes and corrective actions.
Diagram of system and introduction to software parameters.
Details parameters P1-01 to P2-35.
Details parameters P2-39 to P4-17.
Details parameters P4-18 to P6-20.
Details parameters P6-21, P8-01, and read-only parameters.
Continues read-only parameters and introduces communication.
Covers RJ45 connector pinout and fieldbus communication.
To Next Page
