To Next PageTo Next Page
What to do if my YASKAWA A1000 shows DC Charge Circuit Fault Uv3?
The YASKAWA Controller DC Charge Circuit Fault (Uv3) indicates that the charge circuit for the DC bus is broken. Cycle power to the drive and check if the fault reoccurs. If it does, replace the drive.
Why is the fan not working on my YASKAWA A1000 showing Fan Fault EF3?
If your YASKAWA Controller displays a Fan Fault (EF3), it indicates that the A1000 IP54 enclosure built-in fan is not working properly. Check if connector CN2 (fan) is correctly plugged in, if the fan is running properly, and if the wiring S3/SP/SN is correct according to the control logic used (Sink/Source/Internal Supply).
How to fix Braking Transistor Fault rr on my YASKAWA A1000?
If your YASKAWA Controller shows a Braking Transistor Fault (rr), it means the internal braking transistor is broken. Cycle the power supply. If the fault reoccurs, replace the drive.
What to do if my YASKAWA A1000 shows Cannot Reset CrST?
If your YASKAWA Controller displays the Cannot Reset (CrST) error, it means that a fault reset was input while a Run command was active. Turn off the Run command and then reset the drive.
How to fix Heatsink Overheat oH or oH1 on my YASKAWA A1000 Controller?
If you see a Heatsink Overheat (oH or oH1) error on your YASKAWA Controller, it usually indicates that the surrounding temperature is too high, the cooling fan has stopped, the filter mats are clogged, or the airflow to the heatsink is restricted. Check the surrounding temperature and install cooling devices if needed. Also, inspect the drive cooling fan, replace the filter mats, and ensure clear airflow around the heatsink.
What to do if YASKAWA A1000 shows Motor Overflow?
If your YASKAWA Controller displays a 'Motor Overflow' error, it indicates that the motor may be overloaded or the settings are incorrect. To resolve this, reduce the load on the motor.
Why does my YASKAWA Controller display an Option Communication Error?
An Option Communication Error in your YASKAWA Controller can occur due to: * Loss of connection after initial communication. * Faulty wiring. * Communication data errors caused by noise. * A damaged or improperly connected option card. To fix this, inspect the wiring, reduce noise interference, and if necessary, reinstall or replace the option card.
What to do if YASKAWA A1000 Controller shows Braking Transistor Overload Fault?
If the YASKAWA Controller's braking transistor is overloaded, it might be due to several reasons: * The braking transistor may have reached its overload level. * There could be faulty communications wiring or a short circuit. * Noise might be causing communication data errors. * The option card could be damaged or not properly connected. To resolve this, check the wiring for faults, minimize noise effects, and if the error persists, try reinstalling or replacing the option card.
What does DC Charge Circuit Fault Uv3 mean on YASKAWA A1000 Controller?
If the YASKAWA Controller displays a DC Charge Circuit Fault (Uv3) error, it means the charge circuit for the DC bus is broken. To resolve this, cycle power to the drive and check if the fault reoccurs. If it does, replace the drive.
What does Braking Transistor Fault rr mean on YASKAWA A1000 Controller?
If the YASKAWA Controller displays a Braking Transistor Fault (rr) error, it means the internal braking transistor is broken. To resolve this, cycle the power supply. If the fault reoccurs, replace the drive.
General| Type | AC Drive |
|---|---|
| Series | A1000 |
| Input Voltage | 200-240V, 380-480V |
| Frequency Range | 0-400 Hz |
| Horsepower Range | 0.5 to 1000 HP |
| Power Range | 0.4 to 630 kW |
| Control Method | V/f Control |
| Overload Capacity | 150% for 60 seconds |
| Braking | Dynamic Braking |
| Communication | Modbus |
| Safety | Safe Torque Off (STO) |
| Protection Features | Overcurrent, Overvoltage, Undervoltage, Overheat |
| Operating Temperature | -10 to +50°C |
| Storage Temperature | -20 to 60°C |
| Humidity | 5 to 95% RH (non-condensing) |
| Enclosure | IP20 |
Essential safety information, warnings, and precautions for operating the drive.
List of other manuals and documents relevant to the A1000 series drives.
Critical safety warnings for drive installation, operation, and servicing.
Warnings and precautions related to the risk of electrocution.
Warnings about unexpected motor movement during operation or tuning.
Warnings and precautions related to fire risks during installation and operation.
Warnings about potential crushing injuries during handling or installation.
Warnings about potential burns from hot components after operation.
Warnings regarding potential damage to the drive or connected equipment.
Conditions to maintain CE compliance when using the drive with other devices.
Initial inspection and verification steps after receiving the drive.
Recommended environmental conditions for optimal drive performance.
Guidelines for mounting the drive and required ventilation clearances.
Specific instructions for installing high-capacity drive models.
Physical dimensions and specifications for different drive enclosure types.
Dimensional data for drives with IP20/NEMA Type 1 enclosures.
Dimensional data for drives with IP00 enclosures.
Instructions and precautions for wiring the main power circuit.
Table detailing recommended wiring specifications for the main circuit.
Guidelines for wiring the main circuit using specified fuses and filters.
Precautions for connecting the main circuit power input.
Precautions for connecting the main circuit output to the motor.
Precautions and best practices for grounding the drive unit.
Description of main circuit terminal functions and types.
Recommended fuses for branch circuit protection according to UL standards.
Instructions and precautions for wiring the control circuit.
Recommended torque values for tightening main circuit terminals.
Guidelines for installing EMC filters to comply with EMC standards.
Important considerations and precautions for control circuit wiring.
Overview of the control circuit terminal layout and DIP switches.
Detailed description of the functions of each control circuit terminal.
Wiring practices for low voltage control circuits per NEC standards.
Information on the drive's suitability for circuits with specific RMS amperes.
Overview of the digital operator used for programming and control.
Detailed description of each key on the digital operator and its functions.
Visual guide to the operator's menu structure and navigation.
Step-by-step guide for the initial setup and configuration of the drive.
Precautions to take before and after turning on the drive's power supply.
Guidance on selecting the appropriate control mode for the application.
How to set the drive's duty rating based on application load requirements.
Procedures for automatically setting motor parameters for optimal performance.
Specific auto-tuning method for V/f control applications.
Configuring external references and setting acceleration/deceleration times.
Parameter setting for determining the source of the run command.
Adjusting acceleration, deceleration times, and S-curve profiles.
Defining LOCAL and REMOTE modes for frequency reference and run commands.
Configuration of digital and analog input/output signals.
Assigning functions to multi-function digital input terminals.
Assigning functions to multi-function digital output terminals.
Configuring the functions and signal levels of analog inputs.
Configuring the functions and signal levels of analog outputs.
Steps for performing a test run after initial drive setup.
Parameters for drive initialization and access level selection.
Parameter to select the drive's control mode (V/f, OLV, CLV).
Parameters for initializing drive settings and error resets.
Parameter for selecting drive operation modes.
Parameter to set the source for the frequency reference signal.
Parameter to set the source for the run command signal.
Parameter to define the drive's stopping method.
Parameter to reverse motor direction by changing phase order.
Parameters related to the DC injection braking function.
Parameter to select the carrier frequency and PWM mode.
Parameters for setting and adjusting frequency references.
Parameter for inputting the motor's rated current.
Parameter for inputting the motor's rated slip.
Parameters for configuring the functions of digital input terminals.
Parameters for configuring the functions and signal levels of analog inputs.
Parameters for configuring the functions and signal levels of analog outputs.
Parameters for the drive's electronic motor overload protection.
Parameters to prevent motor stall during operation and deceleration.
Parameters related to the auto-tuning process for induction motors.
Parameters for tracing and displaying information about previous faults.
Parameters for monitoring various drive operating statuses.
Parameters for viewing the history of past faults.
Parameter for selecting digital input and output functions.
Common faults, alarms, causes, and corrective actions for drive operation.
Troubleshooting steps for base block faults related to input status.
Troubleshooting control circuit faults caused by torque limits or motor parameters.
Troubleshooting control circuit faults related to drive connectivity.
Troubleshooting control circuit faults when the terminal board is disconnected.
Troubleshooting issues where faults cannot be reset.
Troubleshooting external faults triggered by an option card.
Troubleshooting external faults triggered by input signals.
Troubleshooting specific external fault inputs.
Troubleshooting ground leakage faults and insulation issues.
Troubleshooting issues with the Safe Disable input function.
Troubleshooting faults related to the Safe Disable function.
Troubleshooting faults related to output phase loss or motor damage.
Troubleshooting overcurrent faults.
Troubleshooting issues with heatsink overheating.
Troubleshooting motor overload conditions.
Troubleshooting drive overload conditions.
Troubleshooting faults related to excessive DC bus voltage.
Troubleshooting faults related to input phase loss or imbalance.
Troubleshooting faults related to the internal braking transistor.
Troubleshooting faults related to the motor thermistor connection.
Troubleshooting faults related to low DC bus voltage.
Troubleshooting faults related to low controller power supply voltage.
Troubleshooting faults related to the DC bus charge circuit.
Errors arising from incorrect parameter settings via the operator.
Errors encountered during the auto-tuning process for motor parameters.
Troubleshooting faults where the motor fails to accelerate as specified.
Troubleshooting faults related to motor speed.
Troubleshooting faults related to current detection.
Troubleshooting errors related to drive's leakage inductance tuning.
Troubleshooting faults caused by excessive V/f settings during auto-tuning.
Troubleshooting alarms related to motor iron-core saturation.
Troubleshooting alarms related to the motor's rated current.
Troubleshooting errors in the calculation of adjusted slip.
Troubleshooting errors in resistance tuning calculations.
Troubleshooting alarms related to leakage inductance calculations.
Troubleshooting alarms related to the no-load current.
Technical specifications for the Safe Disable input function.
Critical safety warnings and precautions for using the Safe Disable function.
Information on implementing and utilizing the Safe Disable feature.
Description of the Safe Disable circuit components and operation.
Explanation of how the Safe Disable function disables drive output (Safe Torque Off).
Procedure to resume normal operation after Safe Disable is activated.
Monitor functions and digital operator display indicators for Safe Disable.
Monitoring the status feedback signal of the Safe Disable circuit.
Information on UL and cUL marks and product safety certifications.
Requirements for installation environment to comply with UL standards.
UL-compliant wiring practices and recommendations for main circuit terminals.
Recommended crimp terminals and tools for UL/cUL compliance.
Recommended fuses for UL compliant branch circuit protection.
UL recognized electronic motor overload protection features.
Parameter for setting the motor's rated current for overload protection.
Parameter to select the type of motor overload protection curve.
Parameter to set the time duration for motor overload protection.
Safety notes for IP00 enclosures concerning external heatsinks and capacitors.
