L3-02 ................................... 153, 156, 226
L3-04 .............................. 136, 137, 154, 226
L3-05 ............................................ 226
L3-06 ........................................153, 226
L3 Stall Prevention Function ...................... 225
L4-01 ............................................ 226
L4 Frequency Detection ........................... 226
L5-01 ........................................143, 227
L5 Fault Reset.................................... 227
L6-01 ............................................ 227
L6-02 ................................... 136, 143, 227
L6-03 ................................... 136, 143, 227
L6 Overtorque Detection .......................... 227
L8: Hardware Protection .......................... 227
L8-01 ........................................138, 227
L8-05 ............................................ 138
L8-10 ............................................ 228
L8-12 ........................................207, 228
L8-18 ............................................ 228
L8-29 ............................................ 207
L8-35 ............................................ 228
L8-38 ........................................156, 228
LED Check ..................................111, 233
LED Operator ...........................22, 74, 75, 90
LF ...........................................128, 133
LO/RE.................................... 76, 85, 114
LOCAL............................................85
Local/Remote Run Selection....................... 212
Local/Remote Selection ........................... 220
Low Voltage Directive ............................ 241
L Protection Function ............................. 225
M
Magnetic Flux Compensation Capacity ............. 213
Main Circuit Connection Diagram ...............42, 51
Main Circuit Terminal Functions.....................46
Main Circuit Terminal Power Supply.................49
Main Circuit Terminals Connection ..................42
Main Circuit Terminal Wiring ..................24, 247
Main Frequency Reference ..........................62
Main Frequency Reference Input.....................53
Maintenance Alarms .............................. 168
Master Speed Reference Lower Limit .............. 216
Maximum Motor Size Allowed (HP) ............... 199
Maximum Motor Size Allowed (kW)............... 201
Maximum Output Frequency ...................... 218
MEMOBUS/Modbus Communication Error ...128,
129,
130, 140
MEMOBUS/Modbus Communications Test Mode
Complete ........................................ 143
MEMOBUS/Modbus Communications Test Mode Error
.................................................. 143
MEMOBUS/Modbus Error Code .................. 232
Memobus/Modbus Error Code ..................... 110
MEMOBUS/Modbus Test Mode Complete ......... 129
Mid Output Voltage A ............................ 125
Minimum Output Frequency...................156, 157
Minimum Output Voltage ......................... 125
Minor Alarms .................................... 128
Minor Faults .................................127, 128
Modes .............................................79
Momentary Power Loss Operation Selection ........ 225
Monitor Output .....................................54
Motor
Does Not Operate When an External Run Command
is Input .......................................... 156
Motor Does Not Operate When the RUN Button on the
Digital Operator is Pressed ........................ 156
Motor Does Not Rotate............................ 150
Motor Hunting and Oscillation Control Parameters
.................................................. 126
Motor Hunting Occurs When Operating With a Light Load
.................................................. 154
Motor is Too Hot ................................. 152
Motor Line-to-Line Resistance.................105, 219
Motor No-Load Current .......................105, 219
Motor Overload ..............................128, 135
Motor Overload Protection Selection ...... 108, 225, 252
Motor Overload Protection Time..........108, 225, 253
Motor Parameters................................. 104
Motor Protection Function......................... 136
Motor protection operation time ................... 109
Motor Rated Current ................ 104, 108, 218, 252
Motor Rated Slip .............................104, 218
Motor Rotates After the Drive Output is Shut Off ... 155
Motor Rotates Faster Than the Frequency Reference
.................................................. 153
Motor Rotates in One Direction Only............... 157
Motor Stalls During Acceleration or With Large Loads
.................................................. 152
Motor Stops During Acceleration or When a Load is
Connected........................................ 157
Motor Wiring ......................................49
Index
YASKAWA ELECTRIC TOEP C710606 26B YASKAWA AC Drive – J1000 Quick Start Guide
259
To Next Page
Loading...
