What to do if my ZOLL Medical Equipment says "CHECK DEFIB PADS"?
If the ZOLL Medical Equipment displays the message "CHECK DEFIB PADS", ensure the defibrillation electrode pads are making proper skin contact and that the patient does not have excessive hair beneath the electrodes. If the message persists, replace the defibrillation cable.
What to do if ZOLL aed pro says "RELEASE SHOCK BUTTON"?
If your ZOLL Medical Equipment displays the message "RELEASE SHOCK BUTTON", release the Shock button. Wait until the unit issues the prompt PRESS FLASHING SHOCK BUTTON before pressing the button.
How to fix noisy ECG, artifact, or wandering baseline on ZOLL aed pro Medical Equipment?
If you are getting a noisy ECG, artifact, or wandering baseline on your ZOLL Medical Equipment, turn off nearby two-way radios and cell phones. Before attaching electrodes, properly prepare the patient’s skin. Check for proper adhesion of the electrodes to the patient. Arrange the cable and leads so that they do not pull on the electrodes or swing excessively.
Why is my ZOLL aed pro Medical Equipment defibrillator not charging?
If your ZOLL Medical Equipment is not charging, verify the rhythm. Confirm that the defibrillation cable is plugged in and the pads are attached to the patient. Install a fully charged battery pack.
How to troubleshoot the "CHECK ECG ELECTRODES ATTACH ECG ELECTRODES" message on ZOLL aed pro Medical Equipment?
If your ZOLL Medical Equipment shows the message "CHECK ECG ELECTRODES ATTACH ECG ELECTRODES", ensure that the ECG cable is connected to each electrode and to the unit. Also, make sure that the ECG electrodes are making good contact with the patient and are not dried out. Try replacing the ECG electrodes or the ECG cable.
What does "PLUG IN CABLE" mean on ZOLL aed pro and how to fix it?
If the ZOLL Medical Equipment displays the message "PLUG IN CABLE", ensure that the electrode cable is properly connected to the unit. Remove the cable and check for bent or broken pins. Replace the electrode cable if necessary.
What to do if Ready indicator shows a red “X” on ZOLL Medical Equipment?
If your ZOLL Medical Equipment shows a red “X” while powered on, turn the unit off and then on again. Follow the prompts to resolve the problem. If the unit continues to fail, take it out of service, and contact ZOLL Technical Service.
What to do if ZOLL Medical Equipment displays "PLUG IN DEFIB CABLE"?
If the ZOLL Medical Equipment displays the message "PLUG IN DEFIB CABLE", check the cable, and replace if necessary.
How to fix a "CHANGE BATTERY" message on ZOLL aed pro Medical Equipment?
If your ZOLL Medical Equipment displays the message "CHANGE BATTERY," replace the battery pack with a fully charged battery pack as soon as possible.
Describes other manuals available for the AED Pro unit.
Explains the manual's formatting, symbols, and warning statements.
Lists and describes symbols that may appear in the document or on equipment.
Information regarding warranty terms and conditions for the AED Pro.
Details essential safety precautions for servicing and operating the AED Pro.
Provides contact information and procedures for technical support.
Outlines the process for returning the AED Pro unit for repair.
Procedure to ensure the unit shows no signs of damage or excessive wear.
Tests the unit's power supply and measures current draw.
Verifies the unit powers on correctly and indicates readiness for use.
Tests pediatric mode functionality and electrode connector type.
Evaluates the energy output of the defibrillator at various settings.
Verifies the unit's compatibility and function with different battery types.
Tests the unit's ability to establish communication with a computer.
Performs a test of the unit's internal discharge mechanism.
Calibrates the unit's patient impedance measurement system.
Verifies the unit's capability to detect disconnected ECG leads.
Calibrates the ECG offset level for accurate readings.
Tests the accuracy and functionality of the unit's real-time clock.
Saves calibration data to the unit's non-volatile memory.
Tests the audio recording feature if the option is installed.
Retrieves and clears error log messages from the unit.
Lists general issues with the unit and their associated corrective actions.
Lists and explains critical error log messages for the AED Pro unit.
Provides guidance on how to use the maintenance tests checklist.
The official checklist for recording AED Pro maintenance test results.
General| Device Type | Automated External Defibrillator (AED) |
|---|---|
| Display | LCD |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| ECG Display | Yes |
| Waveform | Rectilinear Biphasic |
| Voice Prompts | Yes |
| Water Resistance | IP55 |
| IP Rating | IP55 |
| ECG Monitoring | Yes |
| Warranty | 5 years |
| Storage Temperature | -20°C to 60°C |
| Energy Selection | Automatic, configurable |
| CPR Feedback | Real CPR Help |
| Data Recording | Yes |
| Data Storage | Yes |
| Connectivity | USB |
| Shock Energy | Selectable 120J, 150J, 200J |
| Energy Levels | Selectable 120J, 150J, 200J |
To Next Page
