EasyManuals Logo

0N3 X5 System User Manual

0N3 X5 System
59 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #56 background imageLoading...
Page #56 background image
MANUGENX5 - Version 1.01 24.03.2021
© 2021 0N3 s.r.l. - Subject to change without notice
56
10.2 International standards
Safety of machinery
EN ISO 13849-1:2015
Safety of Machinery – Safety related parts of control systems Part 1:
General principles for design
EN ISO 13849-2:2012 Safety of Machinery – Safety related parts of control systems Part 2: Validation
EN 61010-1: 2010 + A1:2019
+ AC:2019-04
Safety requirements for electrical equipment for measurement, control, and
laboratory use
EN IEC 61010-2-201: 2018
Safety requirements for electrical equipment for measurement, control and labora-
tory use - Part 2-201: Particular requirements for control equipment
EMC
EN 61000-6-2:2017
Electromagnetic Compatibility (EMC) Part 6-2: Generic Standards – Immunity for
Industrial Environments
EN 61000-6-4:2007+A1:2011
Electromagnetic Compatibility (EMC) Part 6-4: Generic Standards – Emission
Standard for Industrial Environments
EN 61000-4-2:2009
Electromagnetic compatibility (EMC) Part 4-2: Testing and measurement tech-
niques Electrostatic discharge immunity test
EN 61000-4-3:2006+A2:2010
Electromagnetic compatibility (EMC) Part 4-3: Testing and measurement tech-
niques Radiated, radio-frequency, electromagnetic eld immunity test
EN 61000-4-4:2012
Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement tech-
niques - Electrical fast transient/burst immunity test
EN 61000-4-5:2006
Electromagnetic compatibility (EMC) Part 4-3: Testing and measurement tech-
niques Radiated, radio-frequency, electromagnetic eld immunity test
EN 61000-4-6:2009
Electromagnetic compatibility (EMC) Part 4-6: Testing and measurement tech-
niques - Immunity to conducted disturbances, induced by radio-frequency elds
EN 61000-4-8:2013
Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement tech-
niques Power frequency magnetic eld immunity test
EN 61000-4-29:2000
Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement tech-
niques - Voltage dips, short interruptions and voltage variations on d.c. input power
port immunity tests
ETSI EN 300 328 V2.1.1:2016
Wideband transmission systems; Data transmission equipment operating in the
2,4 GHz ISM band and using wide band modulation techniques; Harmonised Stand-
ard covering the essential requirements of article 3.2 of Directive 2014/53/EU
ETSI EN 301 893 V2.1.1:2017
5 GHz RLAN; Harmonised Standard covering the essential requirements of article
3.2 of Directive 2014/53/EU
ETSI EN 300 330 V2.1.1:2017
Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25
MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Har-
monised Standard covering the essential requirements of article 3.2 of Directive
2014/53/EU
EN 62311:2008
Assessment of electronic and electrical equipment related to human exposure
restrictions for electromagnetic elds (0 Hz - 300 GHz)
ETSI EN 301489-1 V2.1.1
Electromagnetic compatibility and Radio spectrum Matters (ERM) – Electromag-
netic Compatibility (EMC) standard for radio equipment and services – Part1:
Common technical requirements
ETSI EN301489-17 V3.1.1
Electromagnetic compatibility and Radio spectrum Matters (ERM) – Electromag-
netic Compatibility (EMC) standard for radio equipment and services – Part17:
Specic conditions for broadband data transmission system
EN 55011:2007
Industrial, scientic and medical (ISM) radio-frequency equipment - Electromagnet-
ic disturbance characteristics - Limits and methods of measurement

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the 0N3 X5 System and is the answer not in the manual?

0N3 X5 System Specifications

General IconGeneral
Brand0N3
ModelX5 System
CategorySecurity System
LanguageEnglish