3M Clean-Trace LM1 User Manual

EN
(English)
ii
Table of Contents
I. INTENDED USE .................................................. 1
II. USER RESPONSIBILITY ...................................... 1
III. ENVIRONMENTAL OPERATING CONDITIONS ....... 2
IV. INSTRUMENT SPECIFICATIONS .......................... 2
V. LIMITED WARRANTY ......................................... 3
VI. LIMITED WARRANTY AND DISCLAIMER .............. 3
VII. LIMITATION OF LIABILITY ................................. 3
VIII. PRODUCT DESCRIPTION .................................... 3
IX. HOW TO USE THIS MANUAL ............................... 4
X. HOW TO OPERATE THE 3M CLEAN‑TRACE
LUMINOMETER .................................................. 4
a. Operating Controls of the 3M Clean ‑ Trace
Luminometer ...................................................... 4
b. Inserting and removing 3M™ Clean-Trace™ test
swab into the LM1 Luminometer ........................ 5
c. Using the Base ................................................... 5
d. Battery usage and maintenance ......................... 5
e. Charging the battery .......................................... 5
f. When the battery is charged .............................. 6
g. The battery level indicator .................................. 6
h. Power management ........................................... 6
i. Waking the 3M™ Clean ‑ Trace™ Luminometer
from Sleep Mode ................................................ 7
j. 3M Clean-Trace Luminometer Calibration ........... 7
k. How to turn “On” the 3M™ Clean-Trace™ LM1
Luminometer ...................................................... 8
l. The Diagnostic check ......................................... 8
m. Turning Off or Restarting the 3M™ Clean ‑ Trace™
Luminometer ...................................................... 9
n. Controlling the Software ..................................... 9
o. How to Sign in on the 3M™ Clean ‑ Trace™ LM1
Luminometer .................................................... 10
1. On un-registered Luminometer ................................. 10
2. On registered Luminometer – no Pin required ............ 10
3. On registered Luminometer – Pin required .............. 11
p. The Swab Sensor and the Vertical Position Sensor
........................................................................ 12
q. How to look-up Calibration date and Software
details .............................................................. 12
r. How to Sign out of the 3M Clean ‑ Trace LM1
Luminometer .................................................... 12
XI. HOW TO PERFORM A QUICK TEST OR
UNPLANNED TEST ........................................... 13
a. Performing an Unplanned test from an un-
registered Luminometer ....................................... 13
b. Performing an Unplanned test from a registered
Luminometer ........................................................ 13
XII. HOW TO PERFORM A PLANNED TEST RUN ............ 15
a. Performing a Test run on a Test Point within a
Sample Plan ......................................................... 15
b. Restarting an incomplete Sample Plan .................. 15
c. Performing an ATP Test run ................................. 16
d. Performing a Retest on an ATP Test point before
Moving to a Different Test point ........................... 17
e. Performing a Retest on an ATP Test point after
Moving to a Different Test point ........................... 17
f. Performing a Visual Inspection Test on a Test Point
............................................................................ 18
g. Adding a Comment to a Test result ...................... 18
h. Recording Temperature or pH for a Test point within
a Sample plan ...................................................... 19
i. Moving to another Test point in the same Sample
plan ..................................................................... 19
j. Moving to another Test point in a different Sample
plan ..................................................................... 20
k. Viewing Test results ............................................. 20
XIII. HOW TO SYNCHRONIZE THE 3M™ CLEAN‑TRACE™
LM1 LUMINOMETER ............................................. 21
a. Definition ............................................................. 21
b. Setting up Synchronization with a USB Connection 22
c. Setting up Synchronization with a Bluetooth
Connection ........................................................... 22
d. Setting up Synchronization with a Wi-Fi Connection
............................................................................ 23
e. Setting Wi-Fi auto Synchronization Time .............. 24
XIV. PERFORMING ADMINISTRATIVE TASKS ................ 25
a. Setting the Date, Time and Time zone on the 3M™
Clean ‑ Trace™ Luminometer ................................. 25
b. How to adjust the date/time on the 3M™ Clean-
Trace™ LM1 Luminometer ..................................... 25
c. Setting the Time zone ............................................ 26
d. Changing Sleep timeout ....................................... 26
e. Changing the Screen Brightness ........................... 26
f. Resetting the 3M™ Clean-Trace™ Luminometer ... 27
g. Looking up Calibration date and device software
details .................................................................. 27
h. Troubleshooting ................................................... 28
XV. APPENDIX ........................................................... 30
Cleaning and decontaminating the 3M Clean ‑ Trace
Luminometer ...................................................... 30

3M Clean-Trace LM1 Specifications

General

Brand	3M
Model	Clean-Trace LM1
Category	Measuring Instruments
Language	English