ABB ACQ550-x1-06A6-2 - Page 77

ACQ550-U1 User’s Manual 77
Parameters
3421 OUTPUT3 MAX - - Depends on the signal
selected with par. 3415
Group 35: MOTOR TEMP MEAS
3501
SENSOR TYPE 0…6 1 0 (NONE)
3502 INPUT SELECTION 1…8 1 1 (AI1)
3503
ALARM LIMIT Par. 3501 = 1…3: -10…200 °C
Par. 3501 = 4: 0…5000 ohm
Par. 3501 = 5…6: 0…1
1 110 °C / 1500 ohm / 0
3504
FAULT LIMIT Par. 3501 = 1…3: -10…200 °C
Par. 3501 = 4: 0…5000 ohm
Par. 3501 = 5…6: 0…1
1 130 °C / 4000 ohm / 0
Group 36: TIMED FUNCTIONS
3601
TIMERS ENABLE -6…7 1 0 (NOT SEL)
3602
START TIME 1 00:00:00…23:59:58 2 s 00:00:00
3603
STOP TIME 1 00:00:00…23:59:58 2 s 00:00:00
3604
START DAY 1 1…7 1 1 (MONDAY)
3605
STOP DAY 1 1…7 1 1 (MONDAY)
3606 START TIME 2 00:00:00…23:59:58 2 s 00:00:00
3607
STOP TIME 2 00:00:00…23:59:58 2 s 00:00:00
3608
START DAY 2 1…7 1 1 (MONDAY)
3609 STOP DAY 2 1…7 1 1 (MONDAY)
3610
START TIME 3 00:00:00…23:59:58 2 s 00:00:00
3611
STOP TIME 3 00:00:00…23:59:58 2 s 00:00:00
3612 START DAY 3 1…7 1 1 (MONDAY)
3613
STOP DAY 3 1…7 1 1 (MONDAY)
3614
START TIME 4 00:00:00…23:59:58 2 s 00:00:00
3615 STOP TIME 4 00:00:00…23:59:58 2 s 00:00:00
3616
START DAY 4 1…7 1 1 (MONDAY)
3617
STOP DAY 4 1…7 1 1 (MONDAY)
3622 BOOSTER SEL -6…6 1 0 (NOT SEL)
3623
BOOSTER TIME 00:00:00…23:59:58 2 s 00:00:00
3626
…
3629
TIMED FUNC 1…4 SRC 0…31 1 0 (NOT SEL)
Group 37: USER LOAD CURVE
3701
USER LOAD C MODE 0…3 1 0 (NOT SEL)
3702
USER LOAD C FUNC 1=FAULT, 2 = ALARM 11 (FAULT)
3703
USER LOAD C TIME 10…400 s 1 s 20 s
3704
LOAD FREQ 1 0…500 Hz 1 Hz 5 Hz
3705
LOAD TORQ LOW 1 0…600% 1% 10%
3706
LOAD TORQ HIGH 1 0…600% 1% 300%
3707
LOAD FREQ 2 0…500Hz 1Hz 25Hz
3708 LOAD TORQ LOW 2 0…600% 1% 15%
3709
LOAD TORQ HIGH 2 0…600% 1% 300%
3710
LOAD FREQ 3 0…500Hz 1Hz 43Hz
3711
LOAD TORQ LOW 3 0…600% 1% 25%
3712
LOAD TORQ HIGH 3 0…600% 1% 300%
Code Name Range Resolution Default User S