5
IHBI. 1011. 4138500_00
1. GENERAL WARNINGS
The AERMEC HBI heat pump is manufactured according to
the acknowledged technical standards and safety regula-
tions. Designed for air conditioning and the production of
domestic hot water (DHW), it must be destined to this use
compatibly with the performance features. Any contractual
or extracontractual liability of the Company is excluded for
injury/damage to persons, animals or objects owing to
installation, regulation and maintenance errors or improper
use. All uses not expressly indicated in this manual are
prohibited.
The instructions along with all the related documentation
must be given to the user of the system, who assumes the re-
sponsibility to keep the instructions so that they are always at
hand in case of need.
Read this sheet carefully; the execution of all works must
be performed by qualified staff, according to Standards in
force on this subject in different countries. (Ministerial Decree
329/2004).
The appliance must be installed in such a way as to enable
maintenance and/or repairs to be carried out.
The appliance warranty does not cover the costs for ladders,
scaffolding, or other elevation systems that may become nec-
essary for carrying out servicing under warranty.
Do not modify or tamper with the chiller as dangerous situa-
tions can be created and the manufacturer will not be liable
for any damage caused. The validity of the warranty shall be
void in the event of failure to comply with the above-men-
tioned indications.
Ensure periodic cleaning and maintenance of the unit after
normal functioning in order to guarantee a longer useful life
and more reliable operativeness.
The unit must be installed by a qualified and suitably trained
technician, in compliance with the national legislation in force
in the country of destination (Ministerial Decree 329/2004).
AERMEC will not assume any responsibility for damage due
to failure to follow these instructions.
Before beginning any operation, READ THESE INSTRUCTIONS
CAREFULLY AND CARRY OUT THE SAFETY CHECKS TO AVOID
ALL RISKS. All the staff involved must have thorough knowl-
edge of the operations and any dangers that may arise at
the moment in which the installation operations are carried
out.
The HBI units are manufactured with attention to the
individual components in a way to protect both the user and
the installer from any accidents.
After every intervention on the product, qualified staff
are advised to pay particular attention to electric connec-
tions, especially regarding the stripped part of the wires,
which must not exit from the terminal board in any way, thus
preventing the possible contact with live parts of the wire
itself.
This instruction manual, along with the user manual, is an
integral part of the product: make sure that it always accom-
panies the appliance, even if transferred to other owners or
user or is transferred to another system.
It is recommended that the installer instructs the user
regarding appliance functioning and fundamental Safety
Regulations.
The HBI heat pump must be intended for the use for which it
has been expressly manufactured.
THE manufacturer is exempt from any liability, contractual
and extracontractual, for injury/damage caused to persons/
animals and objects, due to installation, adjustment and
maintenance errors and improper use.
After the packaging has been removed, check the integrity
and completeness of the contents.
If this does not comply, contact the dealer where the ap-
pliance was purchased.
Aermec is not liable for any flooding caused by the
intervention of the safety valves.
Dispose of packaging materials in the appropriate contai-
ners at the relevant collection centres.
The waste must be disposed of without hazards for
health and without using procedures or methods
that could damage the environment.
During installation, the user must be informed
that:
- he must periodically check the working pressure
of the hydraulic plant is between 1 and 2 bar, and however
not over 3 bar.
-if necessary, have Technical After-sales Centre professionally
qualified staff intervene
EARTH: the unit must be connected to earth reliably!
If the smell of burning is detected, remove the electric cur-
rent immediately and contact the after-sales centre.
If the anomaly persists, the unit could be damaged and could
cause electric shocks or fires.
Once installation has been performed, voltage can be ap-
plied to the unit only if no problem occurs during the control.
For safety reasons, remember that:
THE HBI heat pump must not be used by children or
unassisted disabled persons.
IT IS dangerous to activate electric devices or appliances
such as switches, household appliances etc., if the smell of
fuel or burning can be detected.
Do not touch the HBI heat pump when you are barefoot or
when parts of the body are wet or humid.
Before performing maintenance, disconnect the heat
pump from the mains electricity, positioning the system
bi-polar switch at off
it is prohibited to modify the safety or regulation devices
without authorisation or indications from the manufacturer
do not pull, disconnect, twist the electric cables leaving the
heat pump even if these are disconnected from the mains
power supply
do not leave containers and inflammable substances in the
room where the appliance is installed
It is prohibited to disperse and leave packaging material
within the reach of children as it cab be a potential source of
danger.
It is prohibited to plug the condensate drain.
Do not climb onto the unit or place anything on it.
Do not use multiple sockets or mobile terminal blocks for
connection of electric cables
To Next Page
Loading...
Need help?
General
