Airo X Series - Default Chapter; Table of Contents

Use and Maintenance Manual – Series X – XS E RESTYLING
Page 3
Tigieffe thanks you for purchasing a product of its range, and invites you to read this manual. Here you can find all the necessary
information for a correct use of the purchased machine. Therefore, you are advised to follow the instructions carefully and to read
the manual thoroughly. The manual should be kept in a suitable place where no damage can occur to it. The content of this manual
may be modified without prior notice and further obligations in order to add changes and improvements to the units already
delivered. No reproduction or translation may take place without the written permission of the owner.
CONTENTS
1. INTRODUCTION ........................................................................................................................................................................ 6
1.1 Legal aspects ........................................................................................................................................................................ 6
1.1.1 Delivery of the machine ............................................................................................................................................... 6
1.1.2 Declaration of commissioning, first check, further periodical checks and transfers of ownership ................................ 6
1.1.2.1 Declaration of commissioning and first check .................................................................................................... 6
1.1.2.2 Further periodical checks ................................................................................................................................... 7
1.1.2.3 Transfers of ownership ....................................................................................................................................... 7
1.1.3 Operators training and information .............................................................................................................................. 7
1.2 Tests performed before delivery ............................................................................................................................................ 7
1.3 Intended use .......................................................................................................................................................................... 7
1.3.1 Leaving at height.......................................................................................................................................................... 8
1.4 Description of the machine .................................................................................................................................................... 8
1.5 Control panels ....................................................................................................................................................................... 9
1.6 Drive power ........................................................................................................................................................................... 9
1.7 Machine life, demolition and decommissioning ..................................................................................................................... 9
1.8 Identification ........................................................................................................................................................................ 10
1.9 Location of main components .............................................................................................................................................. 11
2. TECHNICAL FEATURES OF STANDARD MACHINES .......................................................................................................... 12
2.1 Model XS7 E RESTYLING ................................................................................................................................................ 12
2.2 Model XS8 E RESTYLING LIGHT .................................................................................................................................... 14
2.3 Model XS8 E RESTYLING ................................................................................................................................................ 16
2.4 Model XS8 E RESTYLING - WIND .................................................................................................................................. 18
2.5 Model XS9 E RESTYLING ................................................................................................................................................ 20
2.6 Model X8EW WIND ............................................................................................................................................................. 22
2.7 Model X8EN ...................................................................................................................................................................... 24
2.8 Model X10EW - X10EW-WIND ........................................................................................................................................... 26
2.9 Model X10EN ...................................................................................................................................................................... 28
2.10 Model X12EW - X12EW-WIND ..................................................................................................................................... 30
2.11 Model X12EN ................................................................................................................................................................. 32
2.12 Model X14 EW ................................................................................................................................................................ 34
2.13 Model X14 EN ................................................................................................................................................................ 36
2.14 Model X16 EW ................................................................................................................................................................ 38
2.15 Vibrations and noise ....................................................................................................................................................... 40
3. SAFETY PRECAUTIONS ......................................................................................................................................................... 41
3.1 Personal protective equipment (PPE) ................................................................................................................................. 41
3.2 General safety norms .......................................................................................................................................................... 41
3.3 Use instructions ................................................................................................................................................................... 42
3.3.1 General ...................................................................................................................................................................... 42
3.3.2 Handling ..................................................................................................................................................................... 42
3.3.3 Operating procedures ................................................................................................................................................ 44
3.3.4 Wind speed according to BEAUFORT SCALE .......................................................................................................... 45
3.3.5 Pressure of the machine on ground and load-bearing capacity of ground ................................................................. 46
3.3.6 High-tension lines ...................................................................................................................................................... 47
3.4 Hazardous situations and/or accidents ................................................................................................................................ 47
4. INSTALLATION AND PRELIMINARY CHECKS ..................................................................................................................... 48
4.1 Becoming acquainted with the machine .............................................................................................................................. 48
4.2 Preliminary operation checks .............................................................................................................................................. 48
5. USE INSTRUCTIONS ............................................................................................................................................................... 49
5.1 Platform control panel.......................................................................................................................................................... 49
5.1.1 Drive and steering ...................................................................................................................................................... 50