Align Super Combo TREX 500PRO DFC RH50E01XT - 11. Servo Setting and Adjustment; 12. Gyro and Tail Neutral Setting

11.SERVQ SETIING AND ADJUSTMENT ALIC;;N
To set t his optio n Is to turn on th e transmitte r and con nect to helic opter power . Note : For the safety , please do not con nect ESC to
the bru shless motor before the sett ing in order to prevent any accident cau sed by the moto r run ning d uring the sett ing .
JR TRANSMITIERISERVO
Aileron ' CH2
<; .•
\ Front
Pitch . CHI
FUTABAlHITEC TRANSMmERISERVO
!Pl tch, CHI I
Pos it i on s of CH2&CH6 are not exc hange able,
After assembling as photo (Note; Set the
transmitter under CCPM 120 d&gr ees mod el. pu ll
throttle stick (pitch) upward . If one sWls hplate
serv o (Of two servo s) moves downward, adjust
reverse sw itch (REV) on the trans mitter to make it
move. upward . If three servo move downward,
adjust
the travel value (+.) of SWASH PIT on the
transmitter to make them move u pward . When the
actions of Aileron and Elevator are o ppos ite,
adjust travel values of SWASH AIL and ELE.
Positions of CH1 &C H6 are no t ex ch angeab le,
After
assembling as photo (Note :Set the
tran smitter under CCPM 120 deg rees mode ), pu ll
throttle stic k (pttch ) upward . If one swashplate
se
rvo lor two S8f\1 os ) m oves d own ward. adjust
reverse swi tch (REV) on the transm itt er to make it
mm es up w ard . If three seNO move dow nwa rd,
adjus t the tra v ~ value (+-) of SWASH PIT on the
transm itte r to make them move u pw ard . When the
actions of Al l eron and Elevat or are o pposite ,
adj ust
tn vel valu es of SWASH AIL and ELE.
....
12.ADJUSTMENTS FOR GYRO AND TAIL NEUTRAL SETIING ALIC;;N
Tum off Re voluti on mi xlng (RVMX) mode on the tran smitt er, then set the gai n switc h on the tran smitt er and the gyro to non -Head
l
ock mod e, or disable gain completely . After se tt ing th e tr ansm i tt er, co nnect the helic opt er pow er and pro ceed with rudd er n eutr al
p
oint se tti ng. Not e: Wh en con nec ting to th e h elicopt er power , please do not touch tail rud der slick and th e h elicopter , wait for 3
secon ds f or gyro to enable, and the rudder serv o hom s ho uld be 90 degr ees to Ihe l all servo. Tall pitch slider should be hal fw ay on
the tail output shaft.
This will be the sta ndard rudd er neu tr al p oin t. Aft er co mp leti ng th is sett ing , set th e gain sw itch back to
head
ing lock mod e, with gain at around 70%.
TAIL NEUTRAL SETIING
After the gyro is enable and under non-Head lock mode, correct
setting position of tall seNO and tall pitch assembly is as photo .
If the tall pitch asse mb ly Is not in the mid dle posit ion, please
adjust the length of rudd er control rod to trim .
H EAD LOC KD IREC TlON SETTIN G OF GYRO
To check the head lock dir ection of g yro Is to move the tai l
c
ounterclockwi se and the tall serv o h om wtll be trimm ed
clockwi se. If It trim s in the reverse directi on, please swi tch the
gyro to"R EVERSE" .
I I
Appro • . 4mm
I
I
+- ~
18
Tall mo ving di rect ion
Trim
direction for
b U servo hom .
Back to the cover