Apex Instruments XD-502 - User Manual

62 pages

Save Page as PDF

To Next Page

XD-502

Main Page

Default Chapter3
- Retaining Instructions3
Warranty Policy4
- Table of Contents5
1 Preface9
- Product Introduction9
- Purpose of this Manual9
  - Relevant US EPA Method Descriptions9
- Safety Instructions10
- What to Do When the Unit Arrives12
- How to Transport and Store the Unit13
2 Description of the Product14
- Intended Use and Reasonably Foreseeable Misuse14
  - Source Sampling14
  - Versatile Use14
- Product Compliance14
- System Overview15
  - Sampling Console15
Fig. 1 Example Sampling Syste M15
- Technical Specifications16
- Faceplate Components17
Fig. 2 Front Panel Overview17
Fig. 3 User Interface18
- Menu Overview19
3 Operation18
- User Control Overview18
  - Home Screen Overview18
  - Membrane Switch Pad Buttons18
Fig. 4 Menu Overview19
- Pre-Field Test Operations20
Fig. 5 Front-Side Leak Check21
- Sample Train Leak Check Procedure22
Fig. 6 System Leak Check22
- Field Test Operations23
  - Performing a Method 5 Sampling Test23
- Post-Test Field Operations25
  - Post-Test Calibration Check25
- Setting the Temperature Controller26
  - Set Value Setting26
Fig. 7 Temperature Controller Configuration26
- Operation Using Software27
Fig. 8 PC to Console Connection27
- Main Screen Overview28
Fig. 9 Main Screen Overview28
- Navigation/Connection Section Overview29
Fig. 10 Software Navigation29
Fig. 11 Console Connect Window29
- Traverse Point Section Overview30
- Periodic Save and Auto Stop Section Overviews30
Fig. 12 Traverse Point Section30
Fig. 13 Periodic Save and Auto Stop Sections30
- Volume/Temperature Section Overviews31
Fig. 14 Volume and Temperature Sections31
- Pressure/Console Time Section Overviews32
Fig. 17 Pressure and Console Time Sections32
- Data Point and Note Saving Menu Section Overview33
Fig. 15 Data Point and Note Saving Menu33
- Job Information Screen Overview34
Fig. 16 Job Information Screen Overview34
Fig. 18 Storage Screen Overview35
- Monitor Screen Overview36
Fig. 19 Monitor Screen Overview36
- Utility Screen Overview37
Fig. 20 Utility Screen Overview37
Fig. 21 Wireless Settings Panel Overview38
Fig. 22 Timers Settings Panel Overview39
Fig. 23 Set Date/Time Panel Overview40
Fig. 24 Formats Panel Overview41
Fig. 25 DGM Panel Overview42
- Outline of Sampling Test Operations Using Software43
4 Maintenance45
- Pre-Test Calibrations45
  - Factory Meter Calibration45
  - Initial End User Audits46
- Post-Test Calibrations46
  - Dry Gas Meter46
  - Temperature Sensors46
- Post-Test Maintenance47
- Semi-Annual Maintenance47
  - Annual Maintenance47
  - Manufacturer Support for the Product48
5 Troubleshooting49
- LCD Screen49
  - No Power to LCD Screen49
  - Screen Contrast too DIM or Bright, Cannot Read Characters on Screen49
- Pressures50
  - Pump Motor Running Abnormally50
  - DGM Volume Not Increasing50
- Temperatures51
- Additional Common Console Problems52
6 Diagrams and Schematics53
- Electrical Diagram53
Fig. 26 Electrical Diagram53
- Plumbing Diagram54
Fig. 27 Plumbing Diagram54
- Parts List - Front Panel55
Fig. 28 Parts List - Front Panel55
- Parts List - Interior56
Fig. 29 Parts List - Interior56
7 References and Related Documentation57
- References57
  - EPA and CFR57
- Related Documentation57
  - Apex Instruments Documentation57
- Equations and Nomenclature60
  - Equations60
  - Nomenclature61

Questions and Answers

C
christine47Sep 13, 2025
What to do if the user display doesn’t power on Apex Instruments Laboratory Equipment?
- M
  meghan44Sep 13, 2025
  If the user display on your Apex Instruments Laboratory Equipment doesn’t power on, check connections on the board for proper power input and ensure the console is being used in operational range of -13 to 158 °F (-25 to 70 °C).