31
Multi-turn actuators SA 07.1 – SA 16.1
Operation instructions with actuator controls AMB 01.1/AMB 02.1
No. Type Designation
012
E
Notched pin
019
E
Cheese head screw
020
E
Clamping washer
053
E
Countersunk screw
1.0
B
Housing assly.
2.0
B
Flange, bottom assly.
3.0
B
Hollow shaft assly. (without worm wheel)
5.0
B
Worm shaft assly.
5.12
E
Grub screw
5.32
E
Coupling pin
5.37
B
Pull rod assly.
5.7
E
Motor coupling
5.8
B
Manual drive coupling assly.
6
E
Worm wheel
9.0
B
Planetary gear for manual drive assly.
10.0
B
Retaining flange assly.
14
E
Change-over lever
15.0
B
Cover for switch compartment assly.
17.0
B
Torque lever assly.
18
E
Gear segment
19.0
B
Crown wheel assly.
20.0
B
Swing lever assly.
22.0
B
Drive pinion II for torque switching assly.
23.0
B
Drive wheel for limit switching assly.
24
E
Drive wheel for limit switching
24.0
B
Intermediate wheel for limit switching assly.
25.0
E
Locking plate
27
E
Screw plug
30.0
B
Handwheel with ball handle assly.
39
E
Screw plug
49.0
1)
B
Motor plug, socket assly.
50.0
B
Cover assly.
51.0
B
Socket carrier assly. (with sockets)
52.0
B
Pin carrier (without pins)
53.0
B
Socket for control
54.0
B
Socket for motor
55.0
B
Socket for protective earth
56.0
B
Pin for control
57.0
B
Pin for motor
No. Type Designation
58.0
B
Wire for protective earth
59.0
1)
B
Pin for motor and thermoswitch
in motor plug
60.0
B
Control unit assly. (but without torque head,
without switches)
61.0
B
Torque switching head
70.0
B
Motor
70.1
1)
B
Motor pin carrier
(without pins)
79.0
2)
B
Planetary gearing for motor drive assly.
80.0
3)
B
Output drive Form A assly.
(without thread in stem nut)
80.001
3
E
Thrust bearing set
80.3
3)
E
Stem nut (without thread)
85.0
3)
B
Output drive B3
85.001
3)
E
Snap ring
90.0
3)
B
Output drive D
90.001
3)
E
Snap ring
100
B
Switch for limit / torque switching
(including pins at wires)
105.0
B
Blinker transmitter including pins at wires
(without impulse disc and insulation plate)
106.0
B
Stud bolt for switches
107
E
Spacer
151.0
B
Space heater
152.1
3)
B
Potentiometer (without slip clutch)
152.2
3)
B
Slip clutch for potentiometer
153.0
3)
B
RWG assly.
153.1
3)
B
Potentiometer for RWG
(without slip clutch)
153.2
3)
B
Slip clutch for RWG
153.3
3)
B
Electronic board RWG
153.5
3)
B
Wires for RWG
155.0
3)
B
Reduction gearing
156.0
3)
B
Mechanical position indicator
160.1
3)
E
Protection tube (without cap)
160.2
3)
E
Cap for stem protection tube
S1
S
Seal-kit, small
S2
S
Seal-kit, large
Note:
When placing orders for spare parts, please mention type of actuator and our commission number
(refer to name plate).
1) SA 16.1 with output speeds 32 to 180 rpm without motor plug/socket assly.; motor directly wired to pin carrier (no. 52.0)
2) Only required for some output speeds
3) Not included in basic equipment
To Next Page
Loading...
Need help?
General
