© Banner Engineering Corp. www.bannerengineering.com 30
Q5X ANALOG SPECIFICATIONS
5. Q5X Analog Specifications
Excess Gain
Discrete Output Rating
Current rating: 50 mA maximum
Sensing Beam
IEC 60825-1:2014
Visible red Class 2 laser models, 650 nm
Supply Voltage (Vcc)
12 to 30 V DC (Class 2 supply) (10% max ripple within limits)
Supply Protection Circuitry
Protected against reverse polarity and transient overvoltages
Power and Current Consumption, exclusive of load
< 1 W
Sensing Range
95 mm to 3000 mm (3.74 in to 118.11 in)
Output Configuration
Channel 1: Analog output
Channel 2: Configurable PNP/NPN discrete output or IO-Link
Response Speed
Total response speed varies between 0.5 ms and 2270 ms, depending on
base measurement rate and averaging settings.
For more information, see Averaging on page 20.
Boresighting
± 65 mm at 3000 mm
Delay at Power Up
< 2.5 s
Maximum Torque
Side mounting: 1 N·m (9 in·lbs)
Ambient Light Immunity
5000 lux at 1 m
2000 lux at 2 m
Connector
Integral 5-pin M12 male quick-disconnect connector
Construction
Housing: ABS
Lens cover: PMMA acrylic
Lightpipe and display window: polycarbonate
Temperature Effect (Typical)
< 0.5 mm/°C at < 500 mm
< 1.0 mm/°C at < 1000 mm
< 2.0 mm/°C at < 2000 mm
< 5.0 mm/°C at < 3000mm
Remote Input
Allowable Input Voltage Range: 0 to Vsupply
Active High (internal weak pull-down): High state > (Vsupply – 2.25 V) at 2
mA maximum
Active Low (internal weak pull-up): Low state < 2.25 V at 2 mA maximum
IO-Link Interface
IO Link Revision V1.1
Smart Sensor Profile: Yes
Baud Rate: 38400 bps
Process Data In Length: 32 bits
Process Data Out Length: 8 bits
Minimum Cycle Time: 3.6 ms
IODD files: Provides all programming options of the display, plus additional
functionality.
Application Note
For optimum performance, allow 10 minutes for the sensor to warm up
Environmental Rating
IP67 per IEC60529
Vibration
MIL-STD-202G, Method 201A (Vibration: 10 Hz to 55 Hz, 0.06 inch (1.52
mm) double amplitude, 2 hours each along X, Y and Z axes), with device
operating
Shock
MIL-STD-202G, Method 213B, Condition I (100G 6x along X, Y, and Z axes,
18 shocks), with device operating
Operating Conditions
–10 °C to +50 °C (+14 °F to +122 °F)
35% to 95% relative humidity
Storage Temperature
–25 °C to +70 °C (–13 °F to +158 °F)
Base
Measurement
Rate (ms)
Base
Measurement
Rate in Sync
Mode (ms)
Ambient Light
Rejection
Excess Gain (90% White Card)
at 100 mm at 500 mm at 1000 mm at 2000 mm at 3000 mm
0.5 1.0 Disabled 200 80 25 6 3
1.0 2.0 Enabled 200 80 25 6 3
2.0 4.0 Enabled 920 400 100 25 12
3.0 6.0 Enabled 1600 700 200 50 25
5.0 10.0 Enabled 3200 1400 400 100 50
Black wire specifications per configuration
IO-Link Push/Pull
Output High: ≥ Vsupply - 2.5 V
Output Low: ≤ 2.5 V
PNP
Output High: ≥ Vsupply - 2.5 V
Output Low: ≤ 1V (loads ≤ 1 MegΩ)
To Next Page
Loading...
