Why are the colors pale on my Barco RLM W12?
If the color of the image looks pale on your Barco Projector, it might be due to an improperly connected input signal type (RGB-S/RGBHV/YUV2). Check to make sure that the connections between the projector and the input device are correct.
Why are the colors wrong on my Barco Projector?
If the colors of the projected image are out of place (e.g., displaying red as blue) on your Barco Projector, the G/Y, R/Pr, B/Pb cables from the input might have been incorrectly connected. Please ensure the input source has been correctly connected to the projector.
Why won't my Barco RLM W12 lamp turn on?
If the lamp does not turn on even when the projector has been turned on, the lamp might be damaged. Check the LED indicator on the rear panel of the projector and see if it is blinking in red.
Why is the cooling fan on my Barco RLM W12 so loud?
When the temperature inside the Barco projector rises, the cooling fan will operate at a higher speed to discharge the internal heat more rapidly, causing the noise from the cooling fan to grow louder.
What does it mean when the LED indicator on my Barco RLM W12 Projector is blinking red?
If the LED indicator on the projector’s rear panel is blinking in red, the lamp or the cooling fan could be faulty. Consult the definition of "Page 58 : LED STATUS ".
General| Matrix size | 0.96 \ |
|---|---|
| Heat dissipation | 3412 BTU/h |
| Native aspect ratio | 16:10 |
| Projection distance | - m |
| Projection technology | DLP |
| Contrast ratio (typical) | 1600:1 |
| Screen size compatibility | - \ |
| Projector native resolution | WUXGA (1920x1200) |
| Focal length range | - mm |
| Lamp power | 400 W |
| Lamps quantity | 2 lamp(s) |
| Light source type | Lamp |
| Service life of light source | 1500 h |
| Service life of light source (economic mode) | 2000 h |
| Full HD | Yes |
| Analog signal format system | NTSC |
| Supported graphics resolutions | 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA) |
| BNC input ports | 5 |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | 0 |
| CardBus PCMCIA slot type | No |
| Ethernet LAN data rates | 10, 100 Mbit/s |
| Optical disc player type | Not included |
| Noise level | 43 dB |
| Certification | FCC part 15 Class A, CE EN55022 Class A, CE, TUV, WEEE |
| Dot clock scanning frequency | 165 MHz |
| Placement | Desktop, Ceiling |
| Product type | Large venue projector |
| Product color | Black |
| Market positioning | Presentation |
| Power source | AC |
| AC input voltage | 90 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (max) | 1000 W |
| Power consumption (standby) | 2 W |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 0 - 80 % |
| Sustainability certificates | RoHS |
| Remote control type | IR |
Weight and Dimensions| Depth | 631 mm |
|---|---|
| Width | 500 mm |
| Height | 270 mm |
| Weight | 32000 g |
| Package depth | 830 mm |
| Package width | 669 mm |
| Package height | 448 mm |
Key projector details, accessories, FCC compliance, and safety warnings.
Precautions for electricity, environment, sunlight, lasers, and proper handling.
Orienting, connecting power, and turning on the projector.
Adjusting angle, lens shift, focus, zoom, and keystone correction.
Configuring projection modes and fine-tuning lens for optimal image.
Configuring input sources, power, video standards, and image properties.
Step-by-step guide for safely replacing the projector lamp module.
Table of issues like no power, remote failure, and picture problems with solutions.
To Next Page
