Binder VD 23 - Functional Overview and Menu Structure of the Controller; RD4 Controller Overview; RD4 Controller Menu Structure; MB2 Controller Overview

VD (E3.1) 03/2020 page 3/173
5.3
Performance during and after power failures .................................................................................... 43
5.3.1 RD4 controller ......................................................................................................................... 43
5.3.2 MB2 controller ......................................................................................................................... 44
6. START UP ............................................................................................................ 44
6.1 Condition after establishing the power connection ........................................................................... 44
6.2 Standby mode Turning on and off the vacuum drying oven ............................................................. 45
6.2.1 RD4 controller ......................................................................................................................... 45
6.2.2 MB2 controller ......................................................................................................................... 45
6.3 Controller settings upon start up ....................................................................................................... 46
6.3.1 RD4 controller ......................................................................................................................... 46
6.3.2 MB2 controller ......................................................................................................................... 46
6.4 Vacuum system ................................................................................................................................. 47
6.4.1 Evacuation .............................................................................................................................. 47
6.4.2 Ventilation after completing the drying procedure (flooding with ambient air or inert gas) ..... 48
6.4.3 Ventilation / breaking the vacuum in case of a power failure ................................................. 48
6.4.4 Operation with inert gas .......................................................................................................... 48
7. SET-POINT ENTRY .............................................................................................. 49
7.1 RD4 controller ................................................................................................................................... 49
7.1.1 Temperature set-point entry ................................................................................................... 49
7.1.2 Pressure set-point entry .......................................................................................................... 50
7.2 MB2 controller ................................................................................................................................... 50
7.2.1 Set-point entry through the “Setpoints” menu ......................................................................... 50
7.2.2 Direct setpoint entry via Normal display ................................................................................. 51
8. SETTING SPECIAL CONTROLLER FUNCTIONS .............................................. 52
8.1 Menu structure .................................................................................................................................. 52
8.1.1 RD4 controller ......................................................................................................................... 52
8.1.1.1 “Functions on/off” menu................................................................................................... 52
8.1.1.2 Quick Access menu ......................................................................................................... 53
8.1.2 MB2 controller ......................................................................................................................... 53
8.1.2.1 “Functions on/off” menu................................................................................................... 53
8.1.2.2 “Control on/off” menu ....................................................................................................... 55
8.2 Turning off the vacuum pump via the socket on the pump module .................................................. 55
8.2.1 RD4 controller ......................................................................................................................... 55
8.2.2 MB2 controller ......................................................................................................................... 56
8.3 Using the optional connection “GAS/AIR 2” for ventilation ............................................................... 56
8.3.1 RD4 controller ......................................................................................................................... 57
8.3.2 MB2 controller ......................................................................................................................... 57
8.4 Close all valves ................................................................................................................................. 58
8.4.1 RD4 controller ......................................................................................................................... 58
8.4.2 MB2 controller ......................................................................................................................... 58
8.5 Activating / deactivating temperature control .................................................................................... 59
8.5.1 RD4 controller ......................................................................................................................... 59
8.5.2 MB2 controller ......................................................................................................................... 59
8.6 Activating / deactivating pressure control ......................................................................................... 60
8.6.1 RD4 controller ......................................................................................................................... 60
8.6.2 MB2 controller ......................................................................................................................... 61
8.7 Drying monitoring .............................................................................................................................. 62
8.7.1 RD4 controller ......................................................................................................................... 63
8.7.2 MB2 controller ......................................................................................................................... 63
9. AUTHORIZATION LEVELS AND PASSWORD PROTECTION .......................... 64
9.1 RD4 controller ................................................................................................................................... 64
9.1.1 Password request ................................................................................................................... 64
9.1.2 Assign and modify a password ............................................................................................... 64
9.1.2.1 Assign and modify the User password ............................................................................ 64
9.1.2.2 Assign and modify the Admin password ......................................................................... 65