Default Chapter113

Using the GUI to Configure 802.11N Parameters113
Using the CLI to Configure 802.11N Parameters115
Step 10 to Save Your Changes, Enter this Command116
- Save Config116
Step 4116
- 11Nsupport116
- High Band116
- Information Similar to the Following Appears116
- Low Band116
- MID Band116
- Network116
- Show {802.11A | 802.11B116
Configuring DHCP Proxy118
- Using the GUI to Configure DHCP Proxy118
- Using the CLI to Configure DHCP Proxy119
Configuring Administrator Usernames and Passwords119
- Configuring Usernames and Passwords119
- Restoring Passwords120
Configuring SNMP120
Changing the Default Values of SNMP Community Strings121
- Using the GUI to Change the SNMP Community String Default Values121
- Using the CLI to Change the SNMP Community String Default Values123
Changing the Default Values for SNMP V3 Users123
- Using the GUI to Change the SNMP V3 User Default Values123
- Using the CLI to Change the SNMP V3 User Default Values125
Configuring Aggressive Load Balancing125
- Using the CLI to Configure Aggressive Load Balancing126
- Using the GUI to Configure Aggressive Load Balancing126
Configuring Fast SSID Changing127
- Using the CLI to Configure Fast SSID Changing127
- Using the GUI to Configure Fast SSID Changing127
Enabling 802.3X Flow Control127
Configuring 802.3 Bridging128
- Using the GUI to Configure 802.3 Bridging128
- Using the CLI to Configure 802.3 Bridging129
Configuring Multicast Mode130
- Understanding Multicast Mode130
- Guidelines for Using Multicast Mode131
- Using the GUI to Enable Multicast Mode132
- Using the GUI to View Multicast Groups133
- Using the CLI to Enable Multicast Mode134
- Using the CLI to View an Access Point's Multicast Client Table135
- Using the CLI to View Multicast Groups135
Configuring Client Roaming136
- Inter-Controller Roaming136
- Inter-Subnet Roaming136
- Intra-Controller Roaming136
- Voice-Over-IP Telephone Roaming136
- CCX Layer 2 Client Roaming137
- Using the GUI to Configure CCX Client Roaming Parameters138
- Using the CLI to Configure CCX Client Roaming Parameters139
- Using the CLI to Obtain CCX Client Roaming Information139
- Using the CLI to Debug CCX Client Roaming Issues140
Configuring IP-MAC Address Binding140
Configuring Quality of Service141
- Configuring Quality of Service Profiles141
- Using the GUI to Configure Qos Profiles141
- Using the CLI to Configure Qos Profiles143
- Configuring Quality of Service Roles144
- Using the GUI to Configure Qos Roles144
- Using the CLI to Configure Qos Roles146
Configuring Voice and Video Parameters148
- Bandwidth-Based CAC148
- Call Admission Control148
- Load-Based CAC148
- Expedited Bandwidth Requests149
- Traffic Stream Metrics150
- U-Apsd150
- Using the GUI to Configure Voice Parameters150
- Using the GUI to Configure Video Parameters152
- Using the GUI to View Voice and Video Settings153
- Using the CLI to Configure Voice Parameters158
- Using the CLI to Configure Video Parameters159
- Using the CLI to View Voice and Video Settings160
Configuring EDCA Parameters163
- Using the GUI to Configure EDCA Parameters163
- Using the CLI to Configure EDCA Parameters164
Configuring Cisco Discovery Protocol165
- Using the GUI to Configure Cisco Discovery Protocol168
- Using the GUI to View Cisco Discovery Protocol Information169
- Using the CLI to Configure Cisco Discovery Protocol173
- Using the CLI to View Cisco Discovery Protocol Information174
Configuring RFID Tag Tracking175
- Using the CLI to Configure RFID Tag Tracking177
- Using the CLI to View RFID Tag Tracking Information178
- Using the CLI to Debug RFID Tag Tracking Issues179
Configuring and Viewing Location Settings180
- Installing the Location Appliance Certificate180
- Modifying the NMSP Notification Interval for Clients, RFID Tags, and Rogues181
- Synchronizing the Controller and Location Appliance182
- Using the CLI to View Location Settings182
Configuring the Supervisor 720 to Support the Wism185
- Configuring the Supervisor186
- General Wism Guidelines186
Using the Wireless LAN Controller Network Module187

CHAPTER 5 Configuring Security Solutions5-1190

Chapter 6 Configuring Wlanswireless Device Access311

CHAPTER 7 Controlling Lightweight Access Points373

Chapter 8 Controlling Mesh Access Points453

Chapter 9 Managing Controller Software and Configurations507

Chapter 10 Managing User Accounts537

Chapter 11 Configuring Radio Resource Managementwireless Device Access571

Chapter 12 Configuring Mobility Groupswireless Device Access619

Chapter 13 Configuring Hybrid Reapwireless Device Access649

Appendix673

Safety Considerations and Translated Safety Warnings673

Appendix699

Appendix C End User License and Warranty710

Appendix717

Troubleshooting717

Appendix D Troubleshooting719

Appendix761

Logical Connectivity Diagrams761
- Cisco Wism762

Appendix E Logical Connectivity Diagram762

Brand	Cisco
Model	4400 Series
Category	Controller
Language	English

Cisco 4400 Series User Manual

Table of Contents

Questions and Answers:

Cisco 4400 Series Specifications

Related product manuals