Cisco EF4116 - Page 18

143 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

xviii Cisco 4000 Series Hardware Installation and Maintenance

Document Conventions

Table of Contents

Default Chapter5
- Table of Contents5
Figure 2-38 E1 Interface Cable for 120-Ohm, Balanced Connections (with Twinax Connectors)12
Figure 2-39 E1 Interface Cable for 120-Ohm, Balanced Connections (with RJ-45 Connector)12
- About this Manual15
Chapter 1 Cisco 4000 Series Overview19
- External Differences in Models of the Cisco 4000 Series19
- Figure 1-1 Cisco 4000 Series Chassis-Front Panel20
- Series Specifications20
- Memory Systems22
Chapter 2 Preparing for Installation23
- Safety Recommendations24
  - Safety with Electricity24
  - Preventing Electrostatic Discharge Damage25
- General Site Requirements25
  - Site Environment25
  - Site Configuration Precautions26
- Installation Checklist27
- Required Tools and Equipment28
- Site Log28
- Preparing to Make Connections29
- Console Port and Auxiliary Port Connection Considerations31
- Figure 2-14 EIA/TIA-449 Adapter Cable Connectors, Network End38
- Figure 2-19 Four-Port Serial Port Adapter Cables41
- Figure 2-23 Router Serial Cable Connections43
- Fiber Distributed Data Interface Connections47
Chapter 3 Installing the Router59
- Making Console Port Connections59
- Rack-Mount and Wall-Mount Procedures Overview59
- Making Network Connections60
  - Making Token Ring Connections60
- Making Ethernet Connections61
Chapter 4 Troubleshooting the Initial Hardware Configuration81
- Problem Solving81
  - Troubleshooting the Power and Cooling Systems82
  - Troubleshooting the Network Processor Modules and Cables82
- Environmental Reporting Features83
- Reading Front-Panel LED Indicators83
- Reading Network Processor Module LED Indicators84
  - Ethernet Network Processor Module LED Indicators84
  - FDDI Network Processor Module LED Indicators89
- Token Ring Network Processor Module LED Indicators85
- Four Port Serial Module Indicators86
- Dual Serial Network Processor Module LED Indicators87
Chapter 5 Maintaining and Upgrading the Router95
- Accessing the Router Internal Components95
  - Removing the Component Tray96
  - Memory Replacement Procedures100
- Removing Network Processor Modules98
- Figure 5-11 Removing the Boot Helper Flash Memory SIMM110
- Removing the Cisco 4500-M and Cisco 4700 Boot Helper Flash Memory SIMM110
- Installing Flash-Memory Simms111
Table B-1 Virtual Configuration Bit Meanings117
- Changing Configuration Register Settings118
- Configuring the Boot Field119
Appendix A Cabling Specifications A-1117
Appendix B Cisco 4000 Series Virtual Configuration Register117
- Virtual Configuration Register Settings117
Table B-2 Explanation of Boot Field (Configuration Register Bits 00-03119
Table B-3 Default Boot Filenames120
Table B-4 Configuration Register Settings for Broadcast Address Destination121
Table B-5 System Console Terminal Baud Rate Settings121
- Enabling Booting from Flash Memory122
Appendix C Cisco 4000-M ROM Monitor123
- Available ROM Monitor Commands124
- Entering the Cisco 4000-M ROM Monitor Program125
Table C-1 O Command Options125
Appendix D Cisco 4500-M and Cisco 4700 ROM Monitor127
- Entering the ROM Monitor Program127
Appendix E Operating Conditions for the United Kingdom133
- For United Kingdom Use Only133
Appendix F Operating Conditions for the European Community135

Related product manuals

Preview: Cisco E1200

Preview: Cisco EA2700

Preview: Cisco E-Series

Cisco 15216 EDFA2

Preview: Cisco Linksys E4200

Cisco Linksys E4200

Preview: Cisco Linksys E2500

Cisco Linksys E2500

Cisco Ethernet switch

Preview: Cisco 2501 - Router - EN

Cisco 2501 - Router - EN

Cisco Linksys EtherFast BEFVP41

WS-SUP720-3B - Supervisor Engine 720

Preview: ASR1004 - ASR 1004 Modular Expansion Base

ASR1004 - ASR 1004 Modular Expansion Base

12000 - Series Chassis Modular Expansion Base