Cisco MDS 9700 Series User Manual

User Access Verification
switch login: 2019 Jun 25 15:15:48 switch %SYSMGR-2-SWITCHOVER_OVER: Switchover completed.
2019 Jun 25 15:15:48 switch %ASCII-CFG-6-INFORMATION: Reading ACFG Runtime information
2019 Jun 25 15:15:48 switch %IM-5-IM_MGMT_INTF_STATE: mgmt0 is DOWN
2019 Jun 25 15:15:48 switch %FC-REDIRECT-5-IVR_SUPPORT_ENABLED: IVR Support Enabled in FC_Redirect.
Source: Local Switch - 20:00:84:78:ac:09:35:00
2019 Jun 25 15:15:50 switch %PLATFORM-1-PFM_ALERT: Disabling ejector based shutdown on sup in slot
5
2019 Jun 25 15:15:52 switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_STARTED: Setting boot parameters for
supervisor migration process. It might take some time. Please do not set any config parameters
during this time or do not replace standby.
2019 Jun 25 15:15:56 switch %IM-5-IM_MGMT_INTF_STATE: mgmt0 is UP
User Access Verification
switch login: 2019 Jun 25 15:16:39 switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_COMPLETE: Migration process
is complete now. Supervisor-3 (DS-X97-SF1-K9) in standby slot can now be replaced with Supervisor-4
(DS-X97-SF4-K9).
2019 Jun 25 15:18:00 switch %SYSMGR-2-SBY_SUP_LESS_MEMORY_SLOT: Supervisor in slot 6 is running
with less memory than active supervisor in slot 5
2019 Jun 25 15:18:00 switch %SYSMGR-2-CONVERT_STARTUP_ABORTED: Conversion of startup-config failed.
2019 Jun 25 15:18:00 switch %PLATFORM-2-MOD_PWRDN: Module 6 powered down (Serial number JAE17440HVB)
2019 Jun 25 15:18:00 switch %PLATFORM-5-MOD_STATUS: Module 6 current-status is
MOD_STATUS_CONFIGPOWERED_DOWN
2019 Jun 25 15:18:00 switch %PLATFORM-5-MOD_STATUS: Module 6 current-status is MOD_STATUS_POWERED_DOWN
2019 Jun 25 15:18:00 switch %PLATFORM-2-MOD_REMOVE: Module 6 removed (Serial number JAE17440HVB)
The old active Supervisor-1 Module will be powered down. The supervisor Status LED will be blinking
red, when the supervisor module is powered down by the migration command. If the Status LED is not
blinking red, then check the migration status using the show logging onboard migration status command
on any management session.
Note
Step 10 In a dual supervisor module migration, the first supervisor module migration is complete, the following syslog message
is displayed. Replace your second supervisor module now.
2019 Jun 25 15:18:0 switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_COMPLETE:
Migration process is complete now.
Supervisor-3 (DS-X97-SF1-K9) in standby slot can now be replaced with Supervisor-4 (DS-X97-SF4-K9).
A mix of different Supervisor-4 Modules and Supervisor-1/Supervisor 1E Modules outside a maintenance
window is not supported. This mix of modules is supported only while you are migrating from a
Supervisor-1/Supervisor 1E Module to a Supervisor-4 Module.
Warning
Step 11 (Optional) After the switchover to the Supervisor-4 Module is completed, the boot parameters are set for the supervisor
migration process. Do not set any configuration parameters until the boot parameters are set. After the boot parameters
are set, the migration process is complete. Use the show boot command to display the current boot variables and the
show module command to display the modules installed in the switch.
Supervisor-4 Module outputs
switch# show boot
kickstart variable = bootflash:/m9700-sf4ek9-kickstart-mz.8.4.1.bin
system variable = bootflash:/m9700-sf4ek9-mz.8.4.1.bin
Boot POAP Disabled
switch# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 48 1/10 Gbps Ethernet Module DS-X9848-480K9 ok
Cisco MDS 9700 Series Switches Hardware Installation Guide
127
Installing, Removing, and Verifying Field Replaceable Units
Performing a Nondisruptive Migration

Cisco MDS 9700 Series Specifications

General

Brand	Cisco
Model	MDS 9700 Series
Category	Switch
Language	English